Jump to content
SAU Community

R34 Wheels 10Inch Wide

jimmy21

By jimmy21,
in Exterior & Interior Styling

 Share

Recommended Posts

jimmy21 Contributor

jimmy21

Posted
Posted

Hey guys.

Is there anyway possible to get the wheels in this link to fit on a r34 gtt. Spacers are obviosly required but just some advice would be appreciated. Car has coil over and am prepared to do guard work, dont know how much though. They are 10 inch wide with a -38 offset. they will be a track only wheel and am just trying to pull off a certain look.

http://www.ebay.com.au/itm/230656232879?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649

Cheers

Link to comment
https://www.sau.com.au/forums/topic/379254-r34-wheels-10inch-wide/
Share on other sites
kenjz Collaborator

kenjz

Posted
Posted (edited)

your gonna need a wide kit to fit those in.

unless you camber the shit out of it but then if your gonna take it to a track you will not get any traction.

go for +5 - +15 depending on what look your going for

Edited by kenjz

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      R32 Gtst - Track Car

      By Duncan · Posted

      Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • Dose Pipe Sutututu
      R32 Gtst - Track Car

      By Dose Pipe Sutututu · Posted

      https://www.facebook.com/share/p/18rmVb1SKB/ 
    • GTSBoy
      Leak from Tokico BM50 Brake Master Cylinder

      By GTSBoy · Posted

      The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • No Crust Racing
      R32 Gtst - Track Car

      By No Crust Racing · Posted

      Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • MBS206
      R32 Gtst - Track Car

      By MBS206 · Posted

      I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...