Jump to content
SAU Community

R33 Battery Clamp

Nate85

By Nate85,
in South Australia

 Share

Recommended Posts

Nate85 Apprentice

Nate85

Posted
Posted

Hey guys

I'm having some trouble finding a new battery clamp for my skyline, I've been to multiple places such as supercheap, a few auto elecs and have had no luck so far.

Also went to Nissan dealership but they want to slug me $300 for the cable included which I don't want to spend.

I've attached an image of exactly what I'm after, does anyone have an idea where I could find a replacement easily?

Cheers!

post-62654-0-64744800-1318805060_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/380341-r33-battery-clamp/
Share on other sites
jrm Veteran

jrm

Posted
Posted

Should be able to pick up a regular ground battery clamp from anywhere and then just wire in the cable to it. Not sure why you're having so much issue - is it the size of the terminals? I got sexy gold terminals for mine from Jaycar, I think ..

Aberax Grand Master

Aberax

Posted
Posted

I replaced mine awhile ago. I used some 0 gauge cable, a gold battery terminal connector with volt meter, and a solder/crimp eyelet from Motortraders (now Bursons) for the positive side.

Ground side I used 4 Gauge cable, battery terminal connector and a solder/crimp eyelet.

Carbon 34 Grand Master

Carbon 34

Posted
Posted (edited)

I replaced mine awhile ago. I used some 0 gauge cable, a gold battery terminal connector with volt meter, and a solder/crimp eyelet from Motortraders (now Bursons) for the positive side.

Ground side I used 4 Gauge cable, battery terminal connector and a solder/crimp eyelet.

FYI, always use the same size ground as your power, the current path is from ground to positive .......not positive to negative like most people think. it can cause voltage flucuations and induce noise in the car stereos

dude shite can the factory stuff its junk, and use car audio cable instead, , solder the connections with a butane torch and electronics solder. , heatshrink the terminal. run a ground from the alternator mouning bolt to the battery , or on cars with rear battery, to the factory ground point in the engine bay, it improves the spark, and charging system on unibody cars.

if the factory has currugated split loom on the wire , put in on the new stuff as well, it would be a chaffing protection issue

while your at it dump the factory baby battery if you have one still. get a sealed AGM or Spiral cell one.. you can do both for under 300 bucks if you shop wisely.

4ga(max 120-150 amps) is min for car starting, 0ga(250-300amps) is better, but much harder to work with and cost a bunch more.

Edited by Carbon 34
Aberax Grand Master

Aberax

Posted
Posted

FYI, always use the same size ground as your power, the current path is from ground to positive .......not positive to negative like most people think. it can cause voltage flucuations and induce noise in the car stereos

dude shite can the factory stuff its junk, and use car audio cable instead, , solder the connections with a butane torch and electronics solder. , heatshrink the terminal. run a ground from the alternator mouning bolt to the battery , or on cars with rear battery, to the factory ground point in the engine bay, it improves the spark, and charging system on unibody cars.

if the factory has currugated split loom on the wire , put in on the new stuff as well, it would be a chaffing protection issue

while your at it dump the factory baby battery if you have one still. get a sealed AGM or Spiral cell one.. you can do both for under 300 bucks if you shop wisely.

4ga(max 120-150 amps) is min for car starting, 0ga(250-300amps) is better, but much harder to work with and cost a bunch more.

I think I still have some 0 gauge left, I'll swap it over once I get the car back. The good thing is, it didn't cost my anything either as I knew the guys working at Strathfield when it was still arround.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...