Jump to content
SAU Community

Recommended Posts

Part: 2x 5sp RB20DET gearboxes

Condition: Need reconditioning

Description: 1x from r31 (5th gear 3200rpm @ 100kmh)

1x from r32 (5th gear 2800rpm @ 100kmh)

Location: Morayfield, Qld, 4506

Contact Details: 0406 459 669

Asking Price: $160 ono for the both, or open for swaps for something

Pick-up/Postage Arrangements: Pick-up only as too big for postage. Ring for arrangement

Other Comments:

Hey guys! Sold my r32 a while back so I have decided to get rid of these gearboxes I had for it that are still sitting here.

1st is from an r31 as it has a higher revving 5th gear than an r32 box. It ran fine and had no problems changing into gears when I had it in the car for 2 weeks but it may need reconditioning though as the synchros were quite noisy. Was gonna rebuild it but I don't have the time or money to do so.

2nd is the original gearbox that came out of the r32. Reason I took it out was it was jumping out of 1st and 2nd occasionally and then one day wouldn't shift into any gear at all. May be selector shaft and/or baulk rings, but haven't pulled it apart to have a look. She ran smooth up until then.

With these boxes, you could find that one could fix the other and save some money. Either way I'm over them sitting here. Looking for $160 to get rid of them both.

Give me a call or sms the number above.

Thanks guys

Link to comment
https://www.sau.com.au/forums/topic/380415-qld-fs-2x-5sp-rb20det-gearboxes/
Share on other sites

  • 6 months later...


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...