Jump to content
SAU Community

Recommended Posts

if you return the BOV to stock catch cans are ok if they don't vent to atmosphere

but yeah if you don't care about the possibility of getting defected then yeah get the GT3076

from memory it is about $80 for a power run

  • Replies 70
  • Created
  • Last Reply

Top Posters In This Topic

f**k thats not bad. My old tuner for my ford was free for dyno runs ;)

Ha this vents to atmo

Bov has two settings for plump back at atmo

Eitherway cars off road in 12days try my luck at the track get used to it.

But yea just wanted to see what i could push through it last it had 3inch dump n shitty 2.5inch cat n shiity cat back, now its full 3.5 ;)

Then as always build the car the way i want it

The guys at Jaustech and also simon at morpowa are great as well, Heard good things about willall but I have never used them personally. I don't like boostworx as shaun doesn't use ANY knock detection when tuning, if you had a failing fuel pump it would almost certainly result in a popped motor.

I've also had 2 tunes from him that detonated as soon as the weather got above 25c and needed timing pulled out as he set the knock map to be identical to the normal fuel map.

He also doesn't do a road test/tune touch up nor does he test the cold start functionality, every tune I had had to go back to get him to fix the cold start.

Edited by Rolls

Yep rang up said same shit id probs have round the 220rwkw

But il find out friday afternoon ;) 60bucks for a dyno run

Then when they can fit me in for a tune see what i can get to, as far as i know iv got all

Mods to push the limits of the turbo.

If this is 220ish itl take me weeks to get used to 250 or 270

The internals will be fine for that. all depends on what rear housing youve got, if its the normal nissan highflow bill does your outta luck for that kind of boost., id suggest going a proper 3076, 20psi will see you too 300. mine makes 270 on 16psi easily enough

.... Thats a bit shit. I figured garret internals ment around the 20psi region

It isn't about what it can 'handle' it is about where it stops making power. You could probably run 28psi no worries, but whether you'd make any more power than 15psi all comes down to what combination of wheels are used.

The internals will be fine for that. all depends on what rear housing youve got, if its the normal nissan highflow bill does your outta luck for that kind of boost., id suggest going a proper 3076, 20psi will see you too 300. mine makes 270 on 16psi easily enough

Hypergear has them making 270kw with the stock rear housing, though they get seriously hot and he smashes 20psi+ through them to do that. Wouldn't be very detonation friendly.

Edited by Rolls

I'd run 16psi through it, maybe a touch more if you need too

I'm doing a safe 20psi with N1's on a 22 yr old bottom end. Replaced the gasket with a cometic mls 1.3mm unit, arp head bolts, smoothed head face etc

20psi is fine. Anything over that u wanna start worrying. I have the smallest turbo kit avail meaning it pumps less air at that PSI than a big one (ie a t51 can produce mammoth power at 7psi but is quite laggy and needs cams)... but psi is a matter for the tune, the gasket, the rings and valve seals. nothin to do with anything else - psi is all relative to the heat and volume of the air going in after all...

Put short I reckon 20 is doable on a stock engine in good nick, provided hes not running anything large (by large i mean anything that a) needs cams changed, b) is a single c) is bigger than a 2860-7 equivalent. Once you go over 350kw you're getting into the danger zone. I'd be happy if I got 300kw but really, the feel and response of the car is more important to me than any digits on a dyno chart

-D

Put short I reckon 20 is doable on a stock engine in good nick, provided hes not running anything large (by large i mean anything that a) needs cams changed, b) is a single c) is bigger than a 2860-7 equivalent. Once you go over 350kw you're getting into the danger zone. I'd be happy if I got 300kw but really, the feel and response of the car is more important to me than any digits on a dyno chart

-D

It isn't the psi that kills motors, hell it is hardly ever even the raw torque that kills them, theres a few blokes running over 400kw on stock engines, it is all down to heat and avoiding detonation, the torque limit for stock pistons is pretty damn high, they will withstand 400kw for quite some time if you keep temps under control and have absolutely zero detonation.

All in the tune imo.

Have the same high-flow 3076 internals from last years SAU dyno-day and pulled 274.7kw on 15psi (smaller rear housing), 220+ this year's SAU dyno-day on stock 7-8psi boost without a decent tune - reason for decrease was engine 're-build' as stock bottom end wasn't happy when past 18psi on a cold-chilly morning and thus replaced with forged internals. Therefore would agree that 16psi is a safe place to start with 'upper' limit.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...