Jump to content
SAU Community

Recommended Posts

Just to add, iv got a turbo beanie, and a damn good custom radiator thats huge. Knock sensor never goes over 20 no matter how long i spend in the hills.

Dont know if thats anything to go on as far as reliability and engine safeness

  • Replies 70
  • Created
  • Last Reply

Top Posters In This Topic

Back from willall. I love there cars

212rwkw at 15.5psi they said it was a bit low for the psi, took alook at the pfc and said theres lots that needs retuning.

They said as far as engine and mods go its really good :)

Where did the 270kw figure come from, fairly lol.

as i said earlier i think Jeff tuned on a hub pack dyno

Krishy im making more power on 1.5 psi less at all 4 it possibly just needs a good tune another pound and a half wouldn't hurt

270rwkw came from jeff-speedlab

Yea id like tosee what 250rwkw feels like as this washuge power for me already

lol was it at turbo tune? their dyno gives the most bs figures, 230kw from a stock r33 was the best one I saw.

Yea at poorakais where it was.

Wat happend to him??

But evenstill my 212rwkw made my dads m8's ve gts feel slow

????????????? think ya dads mate was not putting his foot down then lol :teehee:

This is why i figured ihad more than212rwkw.

For such alow numberbelive me guys it feels alot more thanthat.

Hopefully gonna get a tune in a week :)

It feels like I a lot of power as your not really used to it as you said, 210rwkw is good but not earth shattering.

For myself an a lot of others here that'd be slow as hell lol but we all work our way up the power ladder :)

Haha yea i know its nothing special. But i used to borrow my dad's ve ss alot n me n dad could both agree 33 is a fair amount faster.

Eitherway imhappyat the low rwkw reading means its got alot more left in it.

Iv been lucky enough to go in a 415rwkw 32gtr :O break trackion at all four wheels at 130

Thanks heaps guys for recomending willallracing

If i get a tune il update if people are interested in what it can make with a new tune.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...