Jump to content
SAU Community

Recommended Posts

1991 R32 GTR

Car is making 270rwkw on 18 psi on a very safe tune.

GT-C Volk 18x9's all round.

Motor rebuilt approx 8000km ago

Freshly serviced and ready for a new owner.

Reco block + head were used.

chemical clean all parts, full machine, clearance and blueprint.

ACL comp bearings

JE Forged piston kit

H-beam rods

MLSR steel head gasket

oil restrictors

Genuine nissan gasket set

all new hoses

new genuine thermostat

new water pump

new timing belt

nismo radiator cap

new battery

new heater core

re gassed air con

nismo diff bushes

cradle spacers (pineapples)

600cc injectors

nismo plugs

Garret 28/60 turbos -7

Apexi power fc with hand controller

full kakimoto 3' exhaust

blitz 4 stage boost controler

R33 GTR crank

N1 oil pump

momo stearing wheel+ gear knob.

Tomei 310km dash cluster

new slotted rotors all round (dba)

koyo rad radiator

baffled sump

bosch fuel pump

central locking + alarm and immobilizer

Good stereo, good tires

Car interior has been retrimmed in leather

car is extremely well looked after washed every week.

always garaged as long as i owned it in TAS

im looking for 24,000 ono

which i think is fair for such an amazing car.

i am also open to swap + cash or straight swap for something of interest.

post-88564-0-36149900-1319090688_thumb.jpg

post-88564-0-07970200-1319090731_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/380720-fs-freshly-rebuilt-r32-gtr/
Share on other sites

http://www.skylinesaustralia.com/forums/topic/370504-1991-r32-gtr-sniper-mint-condition/page__p__5905955__hl__mint__fromsearch__1#entry5905955

Looks like its one of the better ones out there.

Interesting that your advertising it for I assume more than you bough it for.

Good luck with the sale.

I'm selling it due to just moving to Melbourne work is 45 minutes away so I'm looking for something more standard feels like i would be wasting it putting big Kms on such a nice and powerful car when someone can put it to better use.

hmmmmmmm... i went n saw this car just before you bought it. and i know a fair bit about the car... having said that, this car has history being shane's first 32r and is still impressive..

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...