Jump to content
SAU Community

RB26/30 for sale! Will handle 1000+hp

PVL-747
 Share

Recommended Posts

PVL-747 Community Regular

PVL-747

Posted
Posted (edited)

I am selling my RB26/30 motor built by Subzero Racing.

Spec's include...

Bottom end line bored, o-ringed, heat treated, lunati 4340 rods, forged pistons, chrome moly rings, ARP bolt's, crankshaft balanced and nitrided, engine deburred and blue printed, nismo water pump, RB26 head serviced, race ported, TODA cams 10.2 mm lift 282 deg duration, TODA cam gears, ARP head stud kit, custom Subzero plenum, chrome covers, custom dry sump (does not include pump just the sump itself) or wet sump.

Subzero guarentee's 1000hp. Same motor powered TRY09's to 9.46 @ 151mph.

Sell $13,000.

I'm on the Gold Coast, QLD.

Mob: 0403 185 817.

Conditions of sale: cash only, pick up only.

Cheers

Aaron.

post-192-1131252238.jpg

Edited by PVL-747
Link to comment
https://www.sau.com.au/forums/topic/38089-rb2630-for-sale-will-handle-1000hp/
Share on other sites
  • 3 months later...
  • 1 year later...
  • 7 months later...
PranK Grand Master

PranK

Posted
Posted
wasn't this engine sold about 1 month ago

Are you serious? You reply to an 8 month old thread asking that question?

date='5 Nov 2005

Thread closed...

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • fatz
      Beers and skylines Fatz style

      By fatz · Posted

      Messing around with. Twin kit for. Rb30/26  
    • Kinkstaah
      RB25DE NEO with Haltech ECU

      By Kinkstaah · Posted

      For fuelling the Haltechs have O2WB fuel controllers. Very useful for helping tuning VE and correcting for *small* mistakes. Of course if your injector/cam/trigger/sensor data is just wrong (or for a GTT which is not a GT) then you will get impossible reactions to things. I am sure you know this already but the reason people don't typically put haltechs (or any Aftermarket ECU) on GT's is because there's practically no real gains to be had - So this knowledge won't be commonplace.
    • ChriscoDom
      Rear Sway Bar Busshings - Holden Astra TS (2002)

      By ChriscoDom · Posted

      Can someone tell me if the cracks seen in the rear sway bar bushings in these photo's is unacceptable from a roadworthy point of view?  
    • GTSBoy
      RB25DE NEO with Haltech ECU

      By GTSBoy · Posted

      Shouldn't need a "base map" for anything other than guidance to ignition tuning. You just need the engine capacity right, the injector size right, and something, almost anything, for a VE map. On an NA engine, fuelling is almost completely a function of load signal & rpm. It should run and drive with a completely flat fuel map. It will be too lean under load, but that's easily fixed. We used to tune all ECUs without any base map. There were no such things (until someone had tuned a near stock engine on one, and then they had a "base map".
    • Kinkstaah
      Duncan's V37.......race car?

      By Kinkstaah · Posted

      What did you actually buy/how much did it cost? When I got mine in like.. 2017...? 2019? the aim was to run Torque for gauges via ODB2 and things like Track Addict/Laptimers/Dashcam/Reversecam/Spotify etc. Mine never broke, but I wonder if you've got the same needs (it sounds like it). Cause I liked the idea of being able to do anything with it. That said, yours also cost 3x the cost of what I spent so... food for thought.  
×
×
  • Create New...