Jump to content
SAU Community

Recommended Posts

  • Replies 203
  • Created
  • Last Reply

Top Posters In This Topic

:banana:

Shake Shake Shake

So anyhoo Ive had the t78 on ebay for a few days now...just to see if there is any intrest..and because it looks look bloody hard to get it all to fit in nicely...and yep...reserve has been met :D

Sooooo on the hunt for something that is maybe a bit more responsive on the 1jz....thinking maybe a PT6262...but dunno yet...will see what happens I guess

lol...well 2 hours later the turbo oil drain is fitted....sounds like a simple job yes......LOL

1JZ Soarer = same a TT 300ZX lol

had to take out a steering rack mount bolt, turn it upside down, so the bolt head faces the sky and make up a washer for it.

Looks like the oil drain kit I bought is for a front or rear sump JZ and not the mid sump engine....oh well...its in now...goes around infront of the bottom radiator hose to make sure it clears the manifold (plus its a bit long)

Also discovered the front crank seal is leaking a bit (common JZ problem) so I am covered in oil after being under the car.

Now just have to elongate the holes in the manifold flange (lol flange) which will be fun using my pissy little dremel on stainless....mind you I have ported cast iron heads using it lol

The 6262 exhaust wheel will choke before you can benefit from the high flow front wheel.. I doubt you'll be able to run 30+psi on a gt35 sized exhaust wheel.. Id go straight to the 65 rear wheel and deal with a few hundred extra lag.. What gearbox you running?

Standard Auto Trans for now.

I wasnt really concerned abooooot the 62mm rear wheel, I am more worried about the small split housing.

But how much more lag will the 6266 have? At this stage it looks like the 6262 will only be 500rpm in front of the t78

Will only be turning to 7200rpm until I can build an engine....then It will go OVER 9000! (well more like 8000 lol)

Hmm more research needed

As Lith mentioned in the precision thread plain bearings aren't known for reliability if I was going to run low boost I'd just go with something tested like a 3582.. If you have plans of building the motor I'd scarifices a small amount of lag increase and get the 65 rear then you have the option of turning it up later. If you go 6262 your limiting yourself for a few hundred rpm spool..

yeah, just found a few results of 6265s making 400+kws and reasonable response, so might be the go

MV kit I will probably get...but I am hankering for a manual box, so time will tell what i'm going to do there.

I do like corners more than drag strips these days lol.

I think I have decided on a PT6262 though, and will just wind boost into it until it stops making power...the auto will go pop before the turbo gets into its stride anyway. and 6262s have run 8s in EVO's so we shall see

+ I still have standard cams and head so a 6266 will be wasted on this engine.

will go something silly big if I build a 2J ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Put a fuel pressure gauge on it. Replace the turbos. Probably completely separate issues.
    • What copper washer do you guys use on the bleeder bolts? The existing one I have I had no idea where to find it in a local store, I did buy some online but that are only 1mm thick whereas my old one is 2mm+ thick and when I put the new washer out and squeeze the top radiator hose I can hear a bit of air but not with the old one. Does this matter? The new one doesn't leak, but the inner diameter is a bit loose whereas the old one threads on the bolt.
    • Howdy all, after being out a few weeks ago on a spirited drive in my GTR I have 2 issues that oddly have appeared at the same time. Whilst accelerating quickly through the gears all of a sudden i’ve lost power at the top of third gear (below redline around 6000rpm) for no obvious reason.    From that point onwards the car has been running rich on idle, won’t really rev under load without a ton of black smoke and the odd backfire, and dying as a pull up to a set of lights unless I keep the revs up around 1500rpm. In addition when shutting down the car that same night (I was 10 minutes from home) I noticed one of the turbos was significantly noisy on wind down when shutting off the engine. After letting the car cool down overnight it starts up fine, although once it gets to temp the revs start to creep up and down, the exhaust is darker than it should be and it also sounds like it’s running rich (fat note) I’ve put a new set of plugs in it - no change, the old plugs all seemed OK with two of them being somewhat richer/fueled up than the other 3 with 1 being borderline. I’ve smoked tested the intake system via the front of the Turbos, found a split vacuum hose going to the factory boost gauge sender, which I have since replaced.  Also found another leak on the gasket coming off the rear turbo outlet, have also replaced this. After fixing both of these leaks - still have the running rich issue. I’ve also tried another pair of AFM’s - no change here After pulling off the front turbo intake pipes, there is obvious shaft play in the front turbo, which now hisses loudly on light revvs although I can’t see why this would make the car run funny even under idle. I’m curious to know why it’s running rich before I potentially replace/rebuild turbos. The car is completely stock <50,000kms  other than an exhaust. Oil and coolant are all clear. I haven’t bothered with coil packs as it looks like they won’t be the issue due to condition of the plugs. Any help appreciated as I cry myself to sleep!
    • No probs at all. I used to love trying to dig up obscure info for those in need where possible going back 20+ years on SAU.  I did have another look and couldn't come up with any closer match. I'm leaning towards those skirts in your first pic are custom fitments, cut down/extended or from another car entirely and modded to fit an R34 sedan. I would've thought someone in Japan had them and taken a photo at some stage over the last 2 decades but there's nothing. Someone out there must know surely.
×
×
  • Create New...