Jump to content
SAU Community

Recommended Posts

  • Replies 203
  • Created
  • Last Reply

Top Posters In This Topic

hahah I'm going to try and do it period mod, So it looks like it was wrapped in a bubble in 1997 or something.

So something along the lines of an old school Jap turbo kit (td06H-20g anyone :whistling: )

We shall see, what happens, it has a built A340E and a 3k(ish) stall, so next year sometime I'll drop a 5 speed in it get some big brakes on the front and get into some track work again.

Going to keep this one nice and simple (re: minimal mods) and tidy it up...and the most important thing

DRIVING THE BLOODY THING!

tl;dr? sub 300kws, brakes, drive

yeah or that.

I figure that if I keep it VERY simple I should be right lol

I wasnt planning on selling the Soarer...but this was too good to miss :thumbsup:

Also means I no longer have to keep an eye on my105 for a cheap as chups track car as I'll just use the supra

Back to the Car - I originally thought that the Twin Turbo R wasnt all the much different to the regular JZA70, I initially thought that all it got was much lees weight, recaro seats, momo wheel and Bilstein shocks.

Turns out it also has bigger anti-roll bars and stiffer springs, Now the Bilsteins are long gone (now has KYB's) No plans to change those just yet, as this car will well and truly be a case of if it aint broke don't fix it. May even save a thousand odd bucks on the brake upgrade and throw some track spec pads at it and see how it goes.

so no more soarer????

Still here being picked up just after xmas...did yours sell or are you parting it?

brake rotors and pads first, dont be one of ''those fanboys'' that think they need brembos to be fast.

brakes are pretty average standard, 300x22 with a single piston caliper

Dont fit

There is/was a kit out there that used R33 Gtst Sumitomo calipers and a 324mm rotor, was looking at pics of the kit yesterday and in all honesty it looks rubbish

Wilwood do a kit for under a grand using 330x28mm disks and their forged superlight calipers.

Not a huge fan of the cheaper wilwood calipers, so may buy the hats and get a thicker rotor and their better caliper and have bracket made to suit.

Just stumbled across this pic

I knew the 1JZ had short rods, but not this short

1JZ-gte rod and piston on the left and 2JZ-gte rod and piston on the right, 2JZ rods are shorter than RB30 rods too btw

1jz rod is 125.25mm, and look how solid the thing is! So any plans I did have of rebuilding the 1J down the track just got a whole lot cheaper :D

DSC03034.jpg

1J and 2J pistons also have the same pin height, so they are interchangeable but the piston crowns are slightly differernt

wow that's a short rod, the 1j rod looks alot thicker than the 2j rod too.

the piston skirt looks a little different between the two.

Edited by tweety bird

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...