Jump to content
SAU Community

Recommended Posts

Hi all.... When u installed new clutch, do u need to do "run ins" or " soft drive / no trashing " for at least minimum 500k's before you can trash the clutch hard??..or doesnt matter??i will tell u the reason after why i ask once u guys answer the question first....

Well its one of those things where theres two sides, one say it is essential to wear it in for 500-1000 but other say pretty much you just thrash let it cool down thrash let it cool down a few times and its done. For example if its a track car you really cant afford to much around with driving around for 500km so a couple laps around the track thrash cool down and usually its fine. ive done both ways and have been fine but yeah personally I think its just a warranty precaution clutch companies use so as to guarantee since if you do drive it 500 to 1000 km easy it is certain the clutch will bed in but doing it the quick way if you do overheat it too much you can prematurely wear it so for a street car I would recomend to wear it in proplerly as its no rush but track car gota take the shortcut.

Usually?? Means its not necessarily and you dnt have to right? Well if thats the case i might have wasted my money and possibly will be getting a new clutch again as my new clutch has already been slipping .. Im sending it back to the company as they insist to investigate it further as To why its already slipping..clutch is actually on the way back to the company today, had a chance to see it before it was sent back And the shop owner told me its got all blue marking all over the clutch disk which mean heat.. He said its most likely i didnt do proper run ins.. He told me for atleast the first 500k to take it easy otherwise clutch would worn out easily.. Is this correct? And the owner advice me most likely the clutch company would not cover warranty on it if it finds the faults was me.. Which mean i just wasted alot of $$$!!! Is ther anything i can do about this?? I dnt want to buy another clutch if there is a way out.. Any suggestions as to what i can do if worst comes to worst?

We tell customers at work it's mandatory they take it easy for 1000-1500km. No excessive slipping, 4x4 work (some cases) or general hard driving, towing etc. etc.

Twice had incidents where KNOWN hoons (the type to kick and spin EVERY gear change, everywhere) come back a week later having clutch problems, and the clutch has been obviously abused. Obviously no warranty as soon as the clutch was sent back. One was a V6 VU ute, dual mass flywheel both times, quite expensive.

You'll be hard pressed to find a manufacturer who will give you warranty on a clutch that's been raped on it's first drive.

You don't take a fresh engine to the drags or a drift day and limiter bash...

You don't hang off the brake pedal from 300km/h down to 0 with new pads and rotors...

I dont like your chances with warranty as this is why they put the requirements to wear in. As i said if you try thrash it straight away but you do overheat it too much then yes you can damage it. What exactly did you do how did you drive? And how many kms has it been?

I dont like your chances with warranty as this is why they put the requirements to wear in. As i said if you try thrash it straight away but you do overheat it too much then yes you can damage it. What exactly did you do how did you drive? And how many kms has it been?

Well first things first, i hardly drive my car, i mean like 3x a week and i do get carried away sometimes... Since the clutch was in, i have done 1500 klms and i honestly i did gave it a hard time several times since.. Im no hoon tho..i just wanted how it would feel like with the new clutch in.. I guess im learning it the hard way.. Im pretty new with these sort of stuff..

When i put my new clutch in i was told to use it, not abuse it (ie, no clutch kicking, 6k launches etc).

I've been reasonably heavy footed on it since day 1 and have never had an issue.

Yeah but you have an awesome clutch

Clutch should be bed in - always.

Button clutches, not so much - they kinda find their own way if you know what I mean

If you do 6k launches and clutch kick on the first half a dozen drives then expect shit to be problematic.

In fact, clutch kick at all and you need to be slapped. I have never seen the use in clutch kicking, get more power

Clutch should be bed in - always.

I also go by this, clutch companys don't give warranty out to something that looks like its been abused. And going by the sound of yours having heat marks, i wouldn't hold my breathe they'll give you another one.

Was the flywheel machined during the new install? The material on the clutch plate(s) needs to bond with the flywheel smoothly in early life. Any hard launch or general abuse will result in bad surface match, thus leaving nasty crap on the flywheel that will eat your clutch faster and progressively get worse In the first few hundred kays, baby the car off the line. Do a bunch of hill starts, without sliding the clutch at all. Find the balance of the clutch so that you can get off the line without using throttle input until fully disengaged. Drive like this habituously and you will pride yourself on footwork.

WOT throttle is ok whilst not on the clutch. Any product worth its value will bite from the get go. My car performed full power runs on the chassis dyno with a 150km old clutch. Its simply how you make the clutch transfer the power whilst the car is stationary that will determine how long it will live. Have you ever tried to push a 1400 kg vehicle? Our drivetrains dont enjoy it any more than we do!! I found that my pedal feel changed overnight (about 700 km in) and am really happy with it.

Except one time when someone stole my car in broad daylight, drove it 50 metres, then brought it back...

b108a012.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That sounds like an excellent idea. But total self-sufficiency means exactly that. You have no-one else to blame when your system faults out and you have no power for a week or two while it gets fixed. You'd have to go the whole hog and get a diesel genny and all the switchover gear, to get you through such times. And, despite the fact that over 20 years, my system has been pretty reliable**, I have seen so many inverter explosions (or less dramatic deaths), panel and roof JB fires, and so on, over that time, to know that the stuff is the same as any other bulk Chinese manufactured stuff. The failure rate is well above zero - both on the equipment and on behalf of the meth addled installation labour force. And then..... warranty and means of redress against the supplier you bought the gear from. Best I can tell is that only a handful of solar companies are still around within 5 years of starting their advertising pitch. They disappear and phoenix like crazy. So, as per 1st paragraph, I suspect the only way to is go balls deep and spend maybe 2-3 times as much as you might think, so that you have every base covered. Plus, know and understand your gear intimately, so you can diagnose problems, sort them out yourself, etc, etc. Plus, probably have to consider upgrading various parts as the years pass, to maintain compatibility with newer stuff, performance and reliability, etc, etc. Whereas, remaining attached to the grid has an ongoing cost that keeps going up even if you use bugger all power from it. But it does provide the fallback in case of the worst case with your own gear. You either pay up front or as you go, I suspect.
    • Add more solar panels to the array. Call the electricity company and tell them you're moving out... Live off grid electric wise
    • Hi Jasmine. How's the war going?
    • I'm extremely suspicious of the VPP stuff. Best I can tell, you surrender any and all control of your panels and battery to the VPP, because there's no way that anyone could write a sufficiently useful set of "rules" as to how much you would be willing to let out of your export meter at any given time. If one of your main interests is to have enough in your battery every evening to get you through the night without having to import, you could easily find yourself with nothing in your battery at the end of the day, or part way through the night, and then be paying import pricing instead of paying nothing. I cannot see how this cannot come to pass.
    • majority aftermarket is an10 yes, but majority of OEM is An12 r35 OEM cooler lines at close to an 12, the hard line that car uses is almost 20mm  Porsche OEM is also AN12   i figure, if our power levels are close to 1000hp, then AN12 should be a must if many OEM standard power vehicles use AN12
×
×
  • Create New...