Jump to content
SAU Community

Recommended Posts

Hey hows it going i got a R33 Series 2 which can not start, it cranks over but it wont start, it aint sputtering so it wouldnt be a fuel issue, but im thinking it could be down to the spark. The car originally had broken down while driving so i had to get it towed back home. The things i have currently done to the car is a ecu diagnostics check and it came up with 55 so everything is fine according to the ecu. I also chectked the spark plugs and did notice a very small amount of oil on the spark plug i only removed the first 3 spark plugs.

I did check the cables of the distrubator and everything seems fine, i However recently hit a pot hole and had probably caused to dislodge a gasket or something and its been losing a bit of oil latetly which has caused the oil level to go down and has caused a very noticeable amount of oil on the left side of the engine just under the turbo, so im not sure if this has anything to do with it. I also have also started to experience a bit of oil in the inlet system more then i used to, infect i used to not experience any oil.

The main thing i want to know is there any tips were you can guide me what i should do next to see if i can resolve the problem, or a possible sympton that usually causes problems like mine as i have had done a search on the forums and couldn't find anything.

Yours Truly,

Nick

Link to comment
https://www.sau.com.au/forums/topic/381846-r33-not-starting/
Share on other sites

Hi i would be checking the turbo feed line incase it might be cracked or the oil return lines to the sump from the turbo and cylinder head

also check rocker cover bolts.There is not much else there unless you have damaged your sump remove the heat sheilds over your tubo

and it should give you a better inspection.

With your engine not firing it could still be your fuel pump or your crank angle sensor check to see if your fuel line pressurises then the ignition

is switched on and that you also hear the pump prime up.

Ive done the fuel check on the pump and i can hear it prime and ive taken the fuel hose off and gave it a crank and fuel started coming it out. I took of the crank angle sensor and turned the wheel and could hear the injectors going so id say its not that as well.

How would i go by checking the spark and coil packs to know if the problem is a spark related issue?

Pull a coilpack out of the bracket. Plug it in to the loom. Fit a spark plug to the coilpack. Rest the hex of the spark plug against an earth (something metal) and crank. See if the spark plug has a strong arc.

Can u explain more.

Did it stall and now won't start? If so what exactly happened when it stalled?

When it stalled it happened when i engaged the clutch so i thought it would it start up when i disengage it, but it didnt. So i tried cranking it and it kept turning over but it didnt sound like it was spluttering so i was thinking it would be spluttering if it was fuel, if it wasn't most likely something like a ignition or spark problem.

The spark plugs it currently has a brand new Bosch Iridium ones which are gapped at 1.0mm they been working perfectly fine so far i did however check the and they look perfectly fine for something thats been in the car for the past 300ks.

I am however getting a set of coil packs for a series 2 this week and possibly going to change them over to see if its down to the coil packs.

I will try today the spark plug problem and give it a show if its down to the spark

Okay i got the car started i changed the ecu over, however the car now is running quite rich it blows black smoke, i however am having a very rough idle issue it sounds like a really lumpy 69 camero but it sounds like its struggling to stay on and its reving at about 800 rpm, i also get this ticking sound from the turbo and exhaust manifold area.

Would you possibly know what the cause of this could be, im guessing it could be a fuel relay. However i did check the injectors and the only one didnt seem to change in idle was first injector not sure which one it is but its the first one when looking from the front.

However all the others changed when i took the plug out except for that one.

How long did you run it for could be a build up of fuel in the cylinders correct me if I'm wrong. Ticking sound could be a small exhaust leak check to see if all the studs are still there and gaskets are in good condition

I ran it for a good 10minuets, ill reset the fuel pump tomorrow and ill also check the leak i think it could be i need some new studs, as i recently replaced the exhaust gasket. Though the rough idle im sort of worried about it, its quite rough its i got to admit, its a strong vibration, like it would sound awesome in a muscle car not so cool in an import

Okay car aint running rough any more i replaced the exhaust manifold head studs as i saw a bit of carbon build up so ive replaced them however i took the car out for a short drive today and its back firing real bad and its struggling to boost up, however it broke down after 5 minuets again same problem it wont crank over, would you guys were i could check next.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...