Jump to content
SAU Community

Recommended Posts

im currently trying to get my R31/RB25 turbo registered in NSW. took it for an emissions test today and completely failed

using all stock parts for the emissions test bar a 3" exhaust, turbo is at 7 psi.

high flow CAT(i think this may be causing alot of the problem it may be screwed)

any advice on wtf went wrong would be great

here are the test results.

post-88957-0-21318200-1320668750_thumb.jpg

Edited by r31rb25help
Link to comment
https://www.sau.com.au/forums/topic/382353-rb25-failed-nsw-emissions-test/
Share on other sites

Yep.

And why do u need an emmisions test with a standard ecu? Have the rules changed? Try another engineer

apparently i need the test because the engine im using is imported.

im thinking i should just replace the entire exhaust system on it for something with passing this damn test in mind

and i dont know what to to about it dumping about 2x the fuel its allowed to into the exhaust at the moment,

Edited by r31rb25help

dug up my old stock exhaust and put 2 3way CATs on it after some advice from a mechanic, looks like horrid and runs horrid but it will apparently pass.

he also recommended i dont run my intercooler at all just a "straight" pipe.

dug up my old stock exhaust and put 2 3way CATs on it after some advice from a mechanic, looks like horrid and runs horrid but it will apparently pass.

he also recommended i dont run my intercooler at all just a "straight" pipe.

blink.gif

He's trolling for sure. Ask him if he will pay for the new engine after yours goes bang from detonation?

apparently i need the test because the engine im using is imported.

im thinking i should just replace the entire exhaust system on it for something with passing this damn test in mind

and i dont know what to to about it dumping about 2x the fuel its allowed to into the exhaust at the moment,

why is it dumping 2x fuel it should be into the exhaust? if it is overfueling heaps then theres no way it will pass have you got bigger injectors in it or something?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...