Jump to content
SAU Community

Recommended Posts

Hey guys,

A few of us are looking at doing a bit of a crusie down your way some time next year.

What is the best time of year to come down, what time distances are from top to bottom of tassy.

Just starting to get ideas so we can plan what will go on while down your way.

Any ideas would be very helpful.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/382886-tas-cruise/
Share on other sites

From like dev to Hobart I think is about 3-3.5 hours?

if you go down the highway....

use google maps to have a look down the coast lines if you want some good touring roads.

have a look at targa tasmania course, good roads to drive, obviously adhereing to the road rules :thumbsup:

Link to comment
https://www.sau.com.au/forums/topic/382886-tas-cruise/#findComment-6107482
Share on other sites

As a Hobartian I'll be the first to admit. Nice empty country roads are hard to come across down here.

I'd stay up north.

I personally love the west coast. I really enjoyed the road from Devonport to Queenstown via Middlesex then to Hobart. That was a good one. Many Caravans in the summer though :(

Link to comment
https://www.sau.com.au/forums/topic/382886-tas-cruise/#findComment-6109380
Share on other sites

thanks for the reply's.

we are not coming down to tear up the roads instead we are looking for something different and to have a bit of a look around..

Take a look around but be sure to take some good roads getting there, there's awesome driving roads around tassie (the vast majority of which you don't need to break any road rules to enjoy). There's good roads all through the state, but sometimes you just need to know where to look ;) As other people said though, don't bother with good twisty tassie roads too much in the middle of summer unless you want to be going 20kmph behind a caravan of caravans.. see what I did there!? I'd say come down in early March or so, the weather hasn't crapped itself completely yet but most people have gone back to the mainland.

What were you planning on doing while you're down? Link us up with a Google maps trip like this http://g.co/maps/wtpb3 I'm sure people would be more than happy to offer suggestions by moving the points around to add in some awesome driving roads, there's already some nice ones on there such as the sideling (between launceston and scottsdale) the weldborough pass (between weldborough, duh, and st helends) etc... but to truly get an idea of what roads suit we probably need to find out what you want to see first. If you like cheese and wine, we've got something for that, if you like hookers and blow, we've got something for that, if you want a decent night scene, you might want to go back to the mainland :P

Oh, and for travelling times, Google maps is your sexually active partner of choice :) with a small word of warning, dirt roads do exist, Google doesn't care if your paint job is ruined.

Jay

Link to comment
https://www.sau.com.au/forums/topic/382886-tas-cruise/#findComment-6109828
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...