Jump to content
SAU Community

I paid BMT 100%, but the work done is only 70%, what can i do to get this fixed??

r32impul

By r32impul,
in Victoria

 Share

Recommended Posts

Jamezilla Grand Master

Jamezilla

Posted
Posted

Guys - please don't turn this into a BMT sh*t fight.

It's sad to see BMT close - they have been very supportive of us over the last 12-18 months. There are, no doubt, reasons for the workshop closing - and if you would like to discuss it in detail - speak to Damian directly. Stick to facts - not heresay.

The issue that Gary raises is a very valid point - and is an area we all need to pay particular heed to - especially when large numbers are being talked about. Business is business - even the best intentions can go arwy, and this is something that can affect any of us, at any workshop.

So please - lets keep this to be as positive a discussion as it can be - and keep away from any personal comments.

There are some good issues being raised - Adz's post in particular.

Ever wondered why builders provide 'estimates' and not 'quotes' all the time? Vehicle maintenance and modifications are not an exact science... and I know there are things that can be done better - both from a workshop and customer perspective. Surely we can come up with ideas that benefit both parties?

Hopefully Gary's case can be resolved quickly.

  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Latest Posts

    • dbm7
      R34 Skyline climate control unit transistor

      By dbm7 · Posted

      Need to see other side of PCB in that area...ie; I don't see any thru-hole mounting, just soldered vias (smd zeners in SOT23 have 3 legs but only 2 are used, as reflected by PCB tracks)
    • GTSBoy
      Another "where do these lines and plugs go" RB25DET question

      By GTSBoy · Posted

      4 to 5 is fine. It will be slow, but that's better than blowing turbos. I don't have a PS pump idle up solenoid on my car, because... I think when we put the Neo in we retained my R32 lines. But.... From inspecton of the R34 vacuum hose diagram, you can see that the solenoid needs to be connected to the turbo inlet as source of clean air) and the plenum (as source of vacuum - which is the place for the air to flow to to cause the idle to increase). So 3 to 1 is VERY WRONG. 3 should go to either the turbo inlet, or the plenum. Follow the other hose from the PS solenoid and if it goes to the plenum, then your 3 goes to 2 2 would also serve as a bleed port for a boost solenoid.
    • GTSBoy
      R34 GTR Seats / No longer reclining

      By GTSBoy · Posted

      Pull them out and pull more apart. You can't do shit with them still bolted to the floor of the car.
    • GTSBoy
      R34 Skyline climate control unit transistor

      By GTSBoy · Posted

      Yes it is. ZD1 is on the other side of the board. Where ZD1 is marked is clearly opposite a 2 pin device. Our 3 pin device here is not a ZD.
    • QB6SAGR
      Tein Circuit Master- rebuild worth it?

      By QB6SAGR · Posted

      Alright, a little update on this... I called Fulcrum, who used to be the distributor in Australia. No Bueno, they don't service them anymore.  Called shock works, who don't service them but offered to dyno the shocks for performance, and suggested DNA in Sydney might service them.  Called DNA, who also do not service them and basically said they try to steer customers away from tein for this exact reason these days- there is just no support for them anymore apparently.  Both SW and DNA said they are a not necessarily a bad product, but they just don't service the brand or know anyone who does service the brand anymore.  So... I could keep calling around but at this point I think I'll probably just spring for the shockworks product, unless anyone here knows anything.  Cheers 🍻 
×
×
  • Create New...