Jump to content
SAU Community

M35 Bose Spare Wheel Well Sub

MOUTH
 Share

Recommended Posts

whitestag Community Regular

whitestag

Posted
Posted

Chris would proberbly know. From what I've seen playing with mine is they are powered so I jumper or something is needed on the non option deck to power it. Also haven't seen back of a non Bose radio so don't know if they got the space for the plug.

whitestag Community Regular

whitestag

Posted
Posted

Did a quick search as I knew I seen this before.

http://www.skylinesaustralia.com/forums/topic/278390-m35-factory-bose-sub-into-non-bose-stereo/page__fromsearch__1

zei20l Grand Master

zei20l

Posted
Posted

also, no, there is no wiring to the sub for the non-bose cars. but there is an amp built into the sub enclosure, so it wouldnt be difficult to work out the power wires and the audio input

zei20l Grand Master

zei20l

Posted
Posted

no mate i dont, im lacking the mounting screw for the sub to hold it and the spare wheel into the wheel well.

if i did, id have it hooked up already! i THINK it uses a speaker level input from the amps that are usually in the boot of the bose equipped models.

from an aftermarket head unit, i wouldnt imagine it would be too hard to wire up.

for $80 its worth taking the risk! lol

  • 2 weeks later...
Chris Rogers Grand Master

Chris Rogers

Posted
Posted

as a FYI. these need at least a 6Vpp balanced signal into them to run properly.

if its still available can you take a measurement from the base to the top of it. I want to see if I can get it in the spare tyre well of my R32.

Chris Rogers Grand Master

Chris Rogers

Posted
Posted

Hi there, I am in Adelaide & also interested. I have sent you a PM.

you would be better off with the 6x9s that go in the rear shelf of yours..

manc01 Collaborator

manc01

Posted
Posted

you would be better off with the 6x9s that go in the rear shelf of yours..

Would you have any recommendations? While you are at it what about the fronts also? I know that it is subject to personal taste & budget but maybe a rough guide would interest a few people.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MissMintyR33
      R33 persistent issues. P/steering and lag/misfire

      By MissMintyR33 · Posted

      I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • GTSBoy
      Freddy Plenum vs Genuine options RB25

      By GTSBoy · Posted

      My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
    • Murray_Calavera
      R33 persistent issues. P/steering and lag/misfire

      By Murray_Calavera · Posted

      There is a really fun solution to this problem, buy a Haltech (or ECU of your choice) and put the MAF in the bin.  I'm assuming your going to want more power in future, so you'll need to get the ECU at some stage. I'd put the new MAF money towards the new ECU. 
×
×
  • Create New...