Jump to content
SAU Community

[#10151] An Unknown Error Occurred

Rolls
 Share

Recommended Posts

Rolls Grand Master

Rolls

Posted
Posted (edited)

http://www.skylinesaustralia.com/forums/topic/261613-hypergear-hiflow-service-continued/

http://www.skylinesa...-goods-on-oils/

Both of these thread give "[#10151] An unknown error occurred" whenever I post, the post comes up but I get the error each time, both threads are over 100 pages.

Any idea why this happens? Workaround? Or should we just make another "thread #2" once they get to 100 pages?

Edited by Rolls
Link to comment
https://www.sau.com.au/forums/topic/384743-10151-an-unknown-error-occurred/
Share on other sites
Rolls Grand Master

Rolls

Posted
  • Author
Posted

I have an idea, on another forum I frequent when threads get in the 100 page range the deleted posts in that thread start to get towards an entire page of deleted posts, this puts the page count as a whole page greater than the amount of posts the users can see, it results in a page that doesn't exist, but the forum software thinks it should, causes strange things to happen.

Maybe put that to them?

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

That is if it actually gives one - it seems intermittent.

Sometimes i cant post to a certain thread, sometimes i can.

Bit hard to debug intermittent issues like that, when it might not occur for a couple weeks.

As i said - IPB 3.2 has fixed ALL the issues that I know about here on SAU. Everything from permissions to embedding youtube clips. I've also been able to post in the "trouble" threads on the Dev machine... So ye, I think if IPB dont know, then we should go and upgrade sooner rather than later.

Rolls Grand Master

Rolls

Posted
  • Author
Posted

That is if it actually gives one - it seems intermittent.

Sometimes i cant post to a certain thread, sometimes i can.

Bit hard to debug intermittent issues like that, when it might not occur for a couple weeks.

In those two threads I posted it happens 100% of the time for me, it does in fact post the post, but it gives you the error as well, so people often end up reposting the post 100 times thinking it hasn't posted.

Does it happen every time for you on those two threads?

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

No it does not, i just tested again (as i have before)

It's not repeatable and only certain people are having issues. There is no specific trend as to the type of user (access driven). It's totally random with who/when it affects. 100 people might be fine in one thread, but then 5 of those 100 might have issues in another.

PranK Grand Master

PranK

Posted
Posted

Hey Rolls,

Thanks mate, I think that with the time I have off over Chrissy I might just hammer the new 3.2 version so we can release that. There were so many issues in this version of invision and they are all gone in that one. I know its a bastard, but it wont be long. :(

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • dbm7
      R34 Skyline climate control unit transistor

      By dbm7 · Posted

      That's not a transistor --- it's marked ZD1 which makes it a zener diode. As to what the breakdown voltage is, not enough there to divine.
    • bilbo117
      R34 GTR Seats / No longer reclining

      By bilbo117 · Posted

      Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • joshuaho96
      Ethanol Content Sensor - Always at 11%?

      By joshuaho96 · Posted

      The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • GTSBoy
      R34 Skyline climate control unit transistor

      By GTSBoy · Posted

      It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • GTSBoy
      Blue slip

      By GTSBoy · Posted

      South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
×
×
  • Create New...