Jump to content
SAU Community

Recommended Posts

Hi everybody, have had our S2 C34 Stagea for about 3 weeks now and loving it, except for the Xanavi unit which hasnt functioned since we got the beauty ( was told it did use to work, which i doubt very much :angry: ) so am on the hunt for a replacement unit that does work. Have spoken to Nisswreck in SA (on the advise of Chris Rogers on this forum) and they are doubtful they have one, they are going to let me know tomorrow. If they dont, is there anyone out there who has one, and is willing to part with it. All ours does is show the "nissan " screen, does nothing else. Any help/ advise appreciated. Cheers.:thumbsup:post-89570-0-31998100-1325585992_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/387136-wtb-s2-c34-xanavi-unit/
Share on other sites

Hi everybody, have had our S2 C34 Stagea for about 3 weeks now and loving it, except for the Xanavi unit which hasnt functioned since we got the beauty ( was told it did use to work, which i doubt very much :angry: ) so am on the hunt for a replacement unit that does work. Have spoken to Nisswreck in SA (on the advise of Chris Rogers on this forum) and they are doubtful they have one, they are going to let me know tomorrow. If they dont, is there anyone out there who has one, and is willing to part with it. All ours does is show the "nissan " screen, does nothing else. Any help/ advise appreciated. Cheers.:thumbsup:post-89570-0-31998100-1325585992_thumb.jpg

same problem.. think its asking you to insert a cd.

Have you tried pressing the TV button to the left? As somebody else mentioned its on the CD function....

Try pressing the TV button then press the touch screen button to the top right. This will change the TV screen channel. If the cd is stuffed then you can use channel VT1 which is the front input (3.5mm jack I believe)

I have pushed and tried all button combinations. All the unit does is "beep" every minute or so. It wont play cds, and the climate control screen doesnt display unless you switch the car off and startit up again with the A/C on. Then it comes up on the screen, but you cant adjust anything because the touch screen doesnt work. Once the unit beeps, the A/C screen dissapears and it goes back to normal. Only buttons that work are the climate butons down the side of the unit.

I'm on my phone so sorry if this doesnt work... Scroll down to chooks post #26

http://www.skylinesaustralia.com/forums/topic/129786-air-con-filter/page__st__20

Might be of some use

You can entry service/diagnostic mode by holding down the 2 buttons......but its all in Japanese so you'll have to do some translating.

I have the service info showing the sub menus somewhere so I'll see if I can dig it up.

post-49793-0-51854500-1325806134_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...