Jump to content
SAU Community

Recommended Posts

i recently got into a car accident and was uninsured at the time. The guy i hit said he went to a few smash repairs and said the quote to fix the damage was roughly 5.5k, i am no panel beater but i think is overpriced. i have uploaded pictures of the damage but the pictures arnt that good of a quality because they were taken on my phone,to sum it off the extend of the damage looks to be the rear bumper and the reinforcment bar was scraped but not pushed in. Can someone tell me if i am being roughted

thanks for the help

post-87166-0-13911500-1325963655_thumb.jpg

post-87166-0-56112500-1325963691_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/387511-urgent-need-advice/
Share on other sites

If its just a rear bumper bar, then to the extent of the damage described, their ripping you off. whole resprays can be done for 10 grand.

To get it done should be a lot cheaper, (around the thousandish dollar mark)

go get some quotes from some quality workshops, and see what they give u as an estimate, as shopping around is your best option. (if you bring all of the replacement parts/source them yourself, they may even drop the price further)

also if push comes to shove, look for another bumper at a wreckers, this could save you a few $$$ plus bumpers are not overly hard to change over.

Just my 2c of what i know from the industry, hope it helps

:cheers: Aaron.

I would say it may be slightly on higher side but then again I haven't see the car in person and aren't in the industry. I got a light tap in the rear of my R33 GTST and it ended up being approx $3.5K. It pushed in the rear metal plate in the boot and some other things causing it to not line up. The Friday arvo that it happened I almost thought it would buff out however once I started to have a look with the panel beater the damage started to show. The V35's might be stronger in the rear than the R33?

It looks to be a fibreglass rear bar as plastic ones don't tear like that. So, you have to replace the rear bar to start with which may need to come form overseas? The reo bar needs to be fixed if damage or possibly replaced. It may have pushed some of the structure that it bolts to. The panel shop then needs to make the bar fit the car properly as a lot of the time they won't line up with the car. That can take time which equals cost. To paint a rear bar I'd expect $400-500.

Just remember that you cannot always see the damage until some trim is taken off and you can get a good look at things.

I'm not just directing this at you but anyone who reads this.. For the sake of everyone on the road (you included) please get some insurance!!!! I would be so fn angry if I was the one you hit. Imagine if you hit something like a BMW 5 series you could be in a world of hurt, more to the point the poor owner of it would.

I would say it may be slightly on higher side but then again I haven't see the car in person and aren't in the industry. I got a light tap in the rear of my R33 GTST and it ended up being approx $3.5K. It pushed in the rear metal plate in the boot and some other things causing it to not line up. The Friday arvo that it happened I almost thought it would buff out however once I started to have a look with the panel beater the damage started to show. The V35's might be stronger in the rear than the R33?

It looks to be a fibreglass rear bar as plastic ones don't tear like that. So, you have to replace the rear bar to start with which may need to come form overseas? The reo bar needs to be fixed if damage or possibly replaced. It may have pushed some of the structure that it bolts to. The panel shop then needs to make the bar fit the car properly as a lot of the time they won't line up with the car. That can take time which equals cost. To paint a rear bar I'd expect $400-500.

Just remember that you cannot always see the damage until some trim is taken off and you can get a good look at things.

I'm not just directing this at you but anyone who reads this.. For the sake of everyone on the road (you included) please get some insurance!!!! I would be so fn angry if I was the one you hit. Imagine if you hit something like a BMW 5 series you could be in a world of hurt, more to the point the poor owner of it would.

only if they didn't have insurance, which is highly unlikely

as for the damage, it looks like there could be close to that sort of amount of damage. as people have said, it isn't just the bar, but the reo bar, that black grill thing in the bar probably has broken clips and i wouldn't be suprised if the exhaust is bent too. there is also the chance that the reversing sensor wiring is damaged.

Well what happened was he told me the day after the accident it would cost roughly there i asked what they were fixing all he told me was rear reo, rear bar, clips and for them to rematch the colour. Fair enough i told him to go thru insurance as it was to much for me to pay in a lump sum, about a week later he told me he had no insurance so i needed to pay cash so i found it abit sus because on the day of the accident he asked if i wanted to fix it privately or handle it with his insurance

Before handing over any money, arrange for the car to be taken to a pannel beater of your choice as well.

3k for a rear bar seems steep, but then again, I have gotten prices from Nissan Australia before and they weren't cheap

35's are getting to be nearly 10 years old, there should be a few rear bars going at wreckers by now.

Edited by PWND

Its an aftermarket bar so will nissan still know the price?

In that case no. You would have to find out what brand it is and get a price

3k seems like a bit of money for a rear bar. Might include the price of a rear reo as well, but still seems a lot.

As I said, arrange for him to take the car to a pannel beater of your choice and get a quote

Remove/Refit:

R/bar = $55

splash shields = $25

T/lamps = $20

boot trims = $45

r/bar reinforcement = $25

Total:$170

Repairs:

Beaver/Rh Drop panel = $180

Reinforcement = $120

Total:$300

Paint:

R/bar = $180

Reinforcement = $90

Beaver/Rh drop panel = $110

mix/match = $25

Oven Allowance = $75

Total:$480

So labour all up your looking at about $950 mark plus whatever parts you may need....IMO i think you're getting ripped

I'm a motor assessor and these are the figures i'd allow from quotes (this is just going by what i can see in the pics)

Hope that helps :D

Remove/Refit:

R/bar = $55

splash shields = $25

T/lamps = $20

boot trims = $45

r/bar reinforcement = $25

Total:$170

Repairs:

Beaver/Rh Drop panel = $180

Reinforcement = $120

Total:$300

Paint:

R/bar = $180

Reinforcement = $90

Beaver/Rh drop panel = $110

mix/match = $25

Oven Allowance = $75

Total:$480

So labour all up your looking at about $950 mark plus whatever parts you may need....IMO i think you're getting ripped

I'm a motor assessor and these are the figures i'd allow from quotes (this is just going by what i can see in the pics)

Hope that helps :D

Tis good to have you along... :thumbsup:

sorry to bump this up, but do not under any circumstance just go off his quote. he could have just gone to a friend and had him quote you a fairytale.

if you are paying out of your own pocket, if he wants to see the money, you both have to agree on a repairer.

otherwise, let him take you to court. ensure you communicate to him in writing that you would like the car inspected at an agreed smash repairer, and you should have no issues.

The court is not going to award the one quote he got from a smash repairer he selected himself.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...