Jump to content
SAU Community

Recommended Posts

Got pulled over in Moore last weekend on the way to a wedding, 25 mins later, an missed the wedding ceremony, they got down smelt the exhaust, an said it smells a little "fumey"

so i now got a defect that says

*Ensure exhaust system complies with manufactures specs

*ensure exhaust emissions comply with manufactures specs

Where am i supposed to get it checked at?

says i gotta produce the vehicle for a full safety certificate inspection, at an approved inspection station.

Is that nearly any mechanic shop? an i take it it has to pass an emissions test to??? does a normal mechanic check that?

Though got a bad feeling its not gunna pass any exhaust test without doin somethin dodgey. Owned the car fo four years an no cops ever mentioned the exhaust, why couldnt the city transport department stay where they belong???

Link to comment
https://www.sau.com.au/forums/topic/387948-emissions-defect/
Share on other sites

They're the bad ones. Queensland Transport Inspections.

You'll have to get it complied to standard/legal emissions by yourself or mechanic/tuner.

Exhaust, i'm not sure what they mean by comply with manu specs? You shouldn't have to change it back to stock normally, but this might be different. Unless they mean replacing/refitting a CAT?

You'll have to head of to their inspection spots for a full car run down (very extensive, brakes, lights, under car inspection, suspension, washer jets, wipers etc etc etc)

They'll then probably check your emissions and noise at the same time because its on your defect slip.

you could just stick to the rules to begin with and have it fully engineered, saves on defects.

my car has all documentation including an RTA performed emissions test showing it meets all their requirements which unless you are being a complete dick to the cop or they are on a power trip gets you back on your way fairly promptly.

the emissions test will be to what ever ADR required for the year your car was manufactured unless you have a crappy system like VIC that decided ADR was silly and made their own on top.

exhaust system compliance is basically number of cats the car came with or more and below the required ADR noise level for that year of manufacture. (more than likely 91db or less)

you could just stick to the rules to begin with and have it fully engineered, saves on defects.

my car has all documentation including an RTA performed emissions test showing it meets all their requirements which unless you are being a complete dick to the cop or they are on a power trip gets you back on your way fairly promptly.

the emissions test will be to what ever ADR required for the year your car was manufactured unless you have a crappy system like VIC that decided ADR was silly and made their own on top.

exhaust system compliance is basically number of cats the car came with or more and below the required ADR noise level for that year of manufacture. (more than likely 91db or less)

This may not be totally relivant in qld. We dont do the whole engineering then lodge at rta thing. Give them a call and ask what you need to do. It will probably need the really strict inspection as mentioned here previosly but you may get away with just providing a rwc from any mechanci you can get to give you one. A stock exhaust may be a good investment if you have to go in and get it inspected.

Hmm looks like I had better keep taking the Mazda to Kingaroy instead of the GTR...every time I go up at night time i get stopped in Nanango but never Moore....and it sounds like I would like to keep it that way!

Defects in Qld, all 3 times I just took it to Qld transport and they inspected it and said replace this and that, went and did it and they signed the paperwork.

Although a defect for having a smelly exhaust sounds a bit stupid. Like my wife's Honda accord euro has a smelly exhaust and its got the factory titanium/stainless exhaust.

Edited by lilcrash

I dont know the ins and outs of it but i think the transport utes can do some forms of testing. They can also order you to go over the pits at transport not just a normal defect any old rwc will clear.

Im sure somebody who has been done by them can add in more on this but its not good if those blokes decide to pull you over.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A realistic expectattion of how long it has to last also comes down to.... when do you think you will be banned from registering and driving old petrol powered shitters? It's 27 years since that thing was built. It probably rusted out 15 years ago. It was probably repaired and looked OK for another 10. If you do a similarish bodge job now, or perhaps slightly better with some actual rust conversion and glassing, then.... get another 10-15 years out of it, after which you'll only be permitted by the CCP to drive electric cars manufactured in their Shenzen zone anyway. 
    • Let me assume that the concern over a manual ECU is that the NeoDET that you have was an auto and has an auto ECU. That ECU will not be a problem, but you WILL have to Nistune it. And you would have to Nistune it even if you had a manual ECU, because the turbo ECUs will shit the bed if they do not have all the things that they were told they have to have, to be happy. The big one being the TCS CU, which you won't have in your car. Anyway, with an auto ECU (which I have running my originally auto NeoDET in an R32) Nistune allows you to put in a Stagea image which doesn't panic about the absent TCS, and allows you to override a whle bunch of other annoyances that would otherwise see the check engine light on 100% of the time. Also, you can't wind up the power very far on the stock NeoDET ECUs without Nistune, because the boost sensor gets in the way. Nistune allows you to push that problem much further up the dial. Do you even have the boost sensor with the engine? Without it, you are SOL and will need an aftermarket ECU (or to find a sensor somewhere, god knows where). I can't tell you what the wiring loom differences are in a 34. But what Duncan said above needs to be considered. When you say "loom", does that include the transmission loom? Because you will need to swap out the auto tranny loom for the equivalent manual loom, and get rid of the neutral/park start interlock (basically hot wire it).
    • I have had the r3c in for years now, maybe close to 7 years and it has never missed a beat, anyone can drive it. Super easy to drive around town, the hotter it gets does get a little hard but it holds the power easy as 
    • Shit thing to find eh? I guess the big issue is that whatever "fix" you do now, it might slow the rust down but won't fix it. I just wanted to add that in no way is fixing sheet metal in 3 dimensions the place to start with welding....that is a pro only job because its too hard to work out where things should be, let alone doing a clean enough job that it can look OK and still be strong too.  I needed to get a new rear quarter panel on the GTR and it took a pro weeks to get the old one off cleanly, new one on in the right place and looking somewhat like it should have with most of the previous connecting panels in place. Gluing a couple of bits of metal together with a welder in the garage is doable, but that is totally different to doing panel  replacement
    • This seems to be a very popular swap since all the turbo skyline prices went through the roof! I'll let someone more familiar chime in, but I understand that yes you probably want to swap the loom in to swap out the auto TCM stuff. You should not assume everything just plugs in either, you need to check at least the ECU wiring diagram for any differences at the plug at the left headlight and probably the ones near the ECU that join the dash loom too  
×
×
  • Create New...