Jump to content
SAU Community

C210 Owners?

Ghostrider
 Share

Recommended Posts

Socrates Mentor

Socrates

Posted
Posted (edited)

Kev from here needs the chrome trim under the window on the drivers side back door.

However the little glass needs to come out for it to be removed, Possible to remove the whole door?

If not that's all good.

Centre Console.

Clips that hold the sun visors up.

Rear view mirror and it's 3 screw plastic mounting piece.

Headlight repeaters on the guards.

On the rear parcel shelf, the little plastic covers which cover the 3 holes on each side for the suspension, i need one.

Bonnet release cable. (All one piece from dash to end of bonnet) not hard to remove, one bolt under dash and one screw on rad support and pull through from drivers seat.

Clutch and brake pedal rubbers.

If they're not all there that's sweet and you will be paid for sure.

As Shaune knows I'm not here to f**k around with anyone, i just love C210s too much.

Edited by Socrates
Link to comment
https://www.sau.com.au/forums/topic/388089-c210-owners/#findComment-6187592
Share on other sites
Socrates Mentor

Socrates

Posted
Posted

Just spoke to Kev

He said try get all the interior bits you can get, door trims, Pillar covers etc. Dont worry about carpets or seats.

Front Grille and Headlight surrounds

Thanks a lot Ghostrider!

Link to comment
https://www.sau.com.au/forums/topic/388089-c210-owners/#findComment-6187595
Share on other sites
V8skylineMAN Grand Master

V8skylineMAN

Posted
Posted

might be easier to grab the whole car, haha

Horn button and the bit that is required to fit it to the steering wheel would be fantastic., and the rear view mirror too please.

Factory radio/tape player.

Cheers for the offer, don't forget to take a packed lunch, you might be there a while!

Link to comment
https://www.sau.com.au/forums/topic/388089-c210-owners/#findComment-6187610
Share on other sites
Ghostrider Grand Master

Ghostrider

Posted
  • Author
Posted

Sorry guys, been n gone, let home at 0800 Sydney time and never saw any of this. I have taken some pics on my phone and are attached, but the front carpet has gone to Mario along with some other bits he needed. I took the vents and surrounds from the console cause I know they break.

I'll give you an idea of the costs, front carpet, dirty as f@#k but intact, console vents, big heater hose under l/h/s of dash, the cover under glove box, and various clips & rubber plugs cost me $20.00.

Can somebody do me a favour and post a picture of the interior rear view mirror and it's mount please, as I have never seen one, but have numerous rear view mirrors here from earlier Nissans I have had.

The sunvisors are intact along with the clips, the chrome mould is also there for rear door, front and rear bumpers in fair straight condition, grille intact, but no headlight surrounds (I got them for Dan once before)

Cheers, D

post-2962-0-19991300-1326520646_thumb.jpg

post-2962-0-86353900-1326520670_thumb.jpg

post-2962-0-14950100-1326520694_thumb.jpg

post-2962-0-93460200-1326520718_thumb.jpg

post-2962-0-59077200-1326520739_thumb.jpg

post-2962-0-09275500-1326520766_thumb.jpg

post-2962-0-35597900-1326520788_thumb.jpg

post-2962-0-95531900-1326520816_thumb.jpg

post-2962-0-49113400-1326520838_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/388089-c210-owners/#findComment-6188122
Share on other sites
Factory 5 Mentor

Factory 5

Posted
Posted

Can you check the condish of the MR30 Rearview mirror? (plus any vent flappy bits that may of survived?)

If you look closely at the bonnet, it has cutouts for 280zx air vents, and the sump has a 'custom; oil drain for the turbo that used to be in it (this car is OLD.... lol)

Link to comment
https://www.sau.com.au/forums/topic/388089-c210-owners/#findComment-6195455
Share on other sites
coupe72001 Mentor

coupe72001

Posted
Posted

Hi Dennis.

If the chrome pieces of trim on the door under the front driver and passenger window don't have a scar from the side view mirrors I'd like them very much! They almost always do though :(

Cheers,

Drew

Link to comment
https://www.sau.com.au/forums/topic/388089-c210-owners/#findComment-6197143
Share on other sites
Socrates Mentor

Socrates

Posted
Posted

Kev from here needs the chrome trim under the window on the drivers side back door.

However the little glass needs to come out for it to be removed, Possible to remove the whole door?

If not that's all good.

Centre Console.

Clips that hold the sun visors up.

Rear view mirror and it's 3 screw plastic mounting piece.

Headlight repeaters on the guards.

On the rear parcel shelf, the little plastic covers which cover the 3 holes on each side for the suspension, i need one.

Bonnet release cable. (All one piece from dash to end of bonnet) not hard to remove, one bolt under dash and one screw on rad support and pull through from drivers seat.

Clutch and brake pedal rubbers.

As above, will update soon with kev's stuff.

Link to comment
https://www.sau.com.au/forums/topic/388089-c210-owners/#findComment-6197948
Share on other sites
Socrates Mentor

Socrates

Posted
Posted (edited)

Just spoke to Kev

He said try get all the interior bits you can get, door trims, Pillar covers etc. Dont worry about carpets or seats.

Front Grille and Headlight surrounds

Thanks a lot Ghostrider!

And also this!

+ external gutter trims

Edited by Socrates
Link to comment
https://www.sau.com.au/forums/topic/388089-c210-owners/#findComment-6197951
Share on other sites
  • 4 weeks later...
sa200b Newbie

sa200b

Posted
Posted

Guys, I've got a set of electric fender mirrors for a C210 with the controller in pretty good condition. Any idea what they are worth? (Sorry to hi-jack)

Hey sparkles, do you still have those mirrors? I'm desperate for some factory mirrors for my 200b. I'm pretty sure they are the same as C210 ones.

Link to comment
https://www.sau.com.au/forums/topic/388089-c210-owners/#findComment-6241569
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
    • r32-25t
      R32 gtr transmission strength, billet plate

      By r32-25t · Posted

      Wouldn’t touch par if they gave it to me. You need to ask how much power you’re looking to make and then add about 50% to it because that’s what you’ll end up making  The factory box says no more at about 350kw or so, the upgraded synchro boxes won’t handle much over 500kw for long and at that point you’re looking at an auto or dog engagement manual,  once you’ve gone dog engagement you may as well go sequential, they cost a little bit more but it’s worth it  also while you’re at it you should upgrade the transfer case with 10 friction plates 
×
×
  • Create New...