Jump to content
SAU Community

Recommended Posts

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

There is also a kind of scorn reserved for those who do the twin system exhausts etc. to stock holden sixes and other non-asian made cars. It is the same illness that effects the 'rice boy'. The strange desire to put a hornet bonnet scoop (not ducted to the underbonnet) on a 4cyl torana is the very same sickness. It all comes down to the owners firm belief that deep down his/her car is faster for the effort.

Beware of playing the same game as the 'trev'. Don't be drawn into a counter culture that likes the 'cheap wine only comes in 5L' stickers. Instead appreciate 'all' performance. It is a truely sad day when the 5L V8 powered whatever kicks your arse whislt you have one of those stickers and believe me there are a few around that WILL kick your arse.

well my mate in his "HYPER' excel twin "PHAT" exhaust, lowered n mags (also spoiler thats bigger than the actual car)

said he was a rice burner, cos he burns on lancers......

2 months later he wrote off his car, slaming into a pole, he said the car was to fast and powerful for him, and wen he said he tried to "drift" around a corner, his back flipped out and lost control.....

i just smilled and said, yer i no....there hell fast aye mate, did u have a kappa sticker on it?

Cool thanks dude, do you know if a knock sensor can be installed on a rotary?

short answer: no. I don't know

long answer: my understanding is that the "knock sensor function" of some bolt on electronics or even the plug and play stuff is that the knock sensor is actually pre-existing and that these just take an electrical feed.

In the R33s, the nock sensor is used by the computer to retard the timing in the event of detonation.

Therefore, my advice would be to check the wiring diagram on the car. It will probably have a knock sensor already.

if not, then you need to ask someone who knows what theyre talking about - probably in a thread related to what you're asking about.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...