Jump to content
SAU Community

Recommended Posts

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

There is also a kind of scorn reserved for those who do the twin system exhausts etc. to stock holden sixes and other non-asian made cars. It is the same illness that effects the 'rice boy'. The strange desire to put a hornet bonnet scoop (not ducted to the underbonnet) on a 4cyl torana is the very same sickness. It all comes down to the owners firm belief that deep down his/her car is faster for the effort.

Beware of playing the same game as the 'trev'. Don't be drawn into a counter culture that likes the 'cheap wine only comes in 5L' stickers. Instead appreciate 'all' performance. It is a truely sad day when the 5L V8 powered whatever kicks your arse whislt you have one of those stickers and believe me there are a few around that WILL kick your arse.

well my mate in his "HYPER' excel twin "PHAT" exhaust, lowered n mags (also spoiler thats bigger than the actual car)

said he was a rice burner, cos he burns on lancers......

2 months later he wrote off his car, slaming into a pole, he said the car was to fast and powerful for him, and wen he said he tried to "drift" around a corner, his back flipped out and lost control.....

i just smilled and said, yer i no....there hell fast aye mate, did u have a kappa sticker on it?

Cool thanks dude, do you know if a knock sensor can be installed on a rotary?

short answer: no. I don't know

long answer: my understanding is that the "knock sensor function" of some bolt on electronics or even the plug and play stuff is that the knock sensor is actually pre-existing and that these just take an electrical feed.

In the R33s, the nock sensor is used by the computer to retard the timing in the event of detonation.

Therefore, my advice would be to check the wiring diagram on the car. It will probably have a knock sensor already.

if not, then you need to ask someone who knows what theyre talking about - probably in a thread related to what you're asking about.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...