Jump to content
SAU Community

Recommended Posts

This seems near impossible, But just wondering if it can be done from up top or underneath with a mirror or torch. Im trying to figure out if I have Garrett 2650 -5's or the standard R32 GTR's. As I been told from someone they are rebuilt R32's and from another that they are 2560 -5' that had the seals redone.

Ive tried from up top. Can only see the oil sender thing, and 1-1 or something marked on it. Should I just give up lol.

Well after an Hour and a half, with 2 jack stands, 2 LED lights and a adjustable mirror, I managed to find..... hahah and read the tag on the turbo. You need to put the mirror inbetween the 2 front pipes, up on the cast side, then search around with the LED's and you will find it.. eventualy.

It Says 14411-06U00. I did a search on this, and apparently its a Nismo one?? so Not the standard R32 GTR turbos :) The previous owner had them rebuilt too. Can anyone shed any light or info on the 14411-06U00's?

To all those that say you can't without removing parts/pipes or taking engine out. you can :) its called determination lol.

Edited by 91BNR32

What is confusing though, is that is the tag I read off the rear Turbo, 14411-06U00 nismo which is fine, "Garrett A/R 42 M24"

Every pic I find for the nismo says "Garrett A/R *****60***** M24" i.e it says 60 not 42.

Edited by 91BNR32

They both suck equally.

Buy something modern and tune it up.

+1

One set are small and laggy, without a decent top end power punch.

Another set are even laggier, but will make a semi-ok top end.

Basically 1980s designs. There are much newer/decent options available.

Ah that sucks :( Whats a good pair of turbo's for the street that will flow 300rwkw under $2000?

These R32 Nismo ones would only have 1000km on them, they were fully stripped and rebuild before I bought the car. I was thinking Id get the car tuned and if I get around the mark, I might just be happy with that. I don't see the point in speding all that money for another 20-30kw & 200-300rpm less laggier, When I'm just after a 300rwkw street only car. Can anyone understand where I'm coming from lol?

Edited by 91BNR32

Ah that sucks :( Whats a good pair of turbo's for the street that will flow 300rwkw under $2000?

These R32 Nismo ones would only have 1000km on them, they were fully stripped and rebuild before I bought the car. I was thinking Id get the car tuned and if I get around the mark, I might just be happy with that. I don't see the point in speding all that money for another 20-30kw & 200-300rpm less laggier, When I'm just after a 300rwkw street only car. Can anyone understand where I'm coming from lol?

There isn't anything under $2,000.

Plus you are not talking 200-300rpm. It'll be more than that. Upwards of 500rpm.

Anyway the rest of the info, funnily enough, if contained in a thread:

www.skylinesaustralia.com/forums/topic/236467-definitive-guide-to-building-300-330awkw-gt-r/

Have a long read of it. Has ALL the info you need.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...