Jump to content
SAU Community

Recommended Posts

Header.jpg

I purchased this car from the last owner, in NSW, who was the first owner in the country and had the car imported through J-Spec. Comes with a folder FULL of instruction manuals for parts, owners handbooks, import papers etc.

Being a factory RWD, it is ~200kg lighter than the AWD version which means better power to weight and more fuel efficient.

Model: 1998 Nissan Stagea RS V - S2

Mileage: 83444 (as of 04 April 2011)

Factory Options:

Rb25det neo

Factory RWD, tiptronic box

Switchable Traction Control

Rear Privacy Glass

Rear Cargo Blind

Rear Cargo Net

5 Piece Floor Mats

Air Con w/Climate Control

Auto Closing Tailgate

Reclining Rear Seat

Dual Airbags

Aftermarket Options:

R33 brakes all round

R33 GTR Intercooler with East Bear piping kit

Brand new battery

CUSCO mechanical LSD

Genuine Dolphin Full Bodykit

NA Grille (Chrome)

Dolphin Roof Panels (to delete ugly black rails on stock Stageas)

Full Re-spray in R34 GTR Z-tune silver

Aftermarket Wing

Nismo Exhaust

Nismo Strut Tower Brace

Currently has Precedeo lowered springs in the rear and standard struts in the front

K&N panel filter

Australian Standard alarm and immobiliser with 2 remotes

High End Sony CD/MD Player and Speakers (Awesome sound setup - model numbers can be found in the instruction manual pic)

SAFC2

18" factory V35 wheels

S14 rear cradle (non Hicas)

Brand new whiteline polyurethane subframe bushes

Brand new tie rod ends

Clear side indicators

HKS EVC3 (not currently installed)

Nismo Aluminium Foot Pedal Covers (Not currently fitted)

Last owner had the boost controller in it and running 12 psi made 297rwhp (219kW) with dyno sheets.

The negatives:

- Front bar has a small amount of damage to the drivers side lower corner. It has been re-fibreglassed from the inside, just the outside visible bit that requires attention if fussy.

- Wing was painted in a rush for Autosalon, the colour match and finish is not perfect but close enough.

- V35 wheels have some scuff marks

For reference sake, the vs-kf in the pics are 18x9.5+2 and 18x9.5+1

Some of the bolt on parts have been removed since the AutoSalon photos, the pics with the V35 wheels are as it sits currently.

Price is $13,500ono and car is located in Adelaide.

100_1605.jpg

100_1608.jpg

100_1614.jpg

100_1611.jpg

100_1607.jpg

stageamanuals.jpg

Add some big wheels and some low;

IMG_7873.jpg

IMG_7892.jpg

40775_137702392934207_109368819100898_157971_754646_n.jpg

stagrear.jpg

Convert to manual and take it sliding for something different - could also leave it auto and do the same as per this video

http://www.youtube.com/watch?v=5ernlW5v1oE

  • 3 weeks later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...