Jump to content
SAU Community

Palm Beach Night Cruise To Kick Start 2012- This Saturday Night, Jan28Th!


Recommended Posts

Hey guys, I think it would be interesting to see some skylines attend this.

DATE: Saturday Night, January 28th

TIME: from 7:45PM

MEET: P6D @ Olympic Park (Cnr of Parkview Drive & Australia Ave)!

WE LEAVE: 8:30PM

Cruise Route:

1. LEFT onto Australia Ave (heading toward Home Bush Bay Drive)

2. At the roundabout, TURN LEFT to merge onto Home Bush Bay Drive.

3. Follow Home Bush Bay Drive to Lane Cove Rd.

4. MERGE RIGHT/TURN RIGHT onto Epping Rd. (follow Signs for Lane Cove/Sydney)! Watch out for 'Pacific Hwy' in 5.1kms as we are turning there... STAY IN LEFT LANE!!!!

5. KEEP LEFT & Turn LEFT onto Pacific Hwy (Sings for Chatswood/Newcastle/Crows Nest)--> DO NOT GO DOWN TOLL WAY!!!

6. In 1.6Kms LOOK FOR Boundary Rd.- Sign for DEEWHY/Manly

7. Turn RIGHT @ Boundary Rd. & follow this to Pittwater Rd. as it turns into Warringah Rd.

8. TURN LEFT onto Pittwater Rd.

9. Follow Pittwater Rd. down through Narrabeen, Mona Vale, Newport, etc. & you will eventually come to PALM BEACH (Parking is next to The GOLF CLUB)

PLEASE KEEP NOISE (Reving, Engine Noise, Music, etc.) TO A MINIMUM, SHOW SOME RESPECT FOR THE RESIDENTS NEARBY TO THE GOLF CLUB & IN THE AREA!!!!

Facebook event link

I'll be going and as you can see there's a whole heap of others as well. Hopefully we can gather some SAU? :D

Kind Regards, Serk

Not yet mate going to see him tomorrow id say hoping to have it sorted by end of the week though

I dunno where anything is in Sydney lol

Hows your car goin Mick_o

Yavuz sort that sh!t or what?

You could also go through McCarr's Creek from Mona Vale Road. Will spit you out at Newport, turn left and you're on your way to Palm Beach. Lots of twisties.

Is it still double demerit points this Sat?



  • Similar Content

  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...