Jump to content
SAU Community

Recommended Posts

THE FIRST FOR 2012

Sat 25 February

And once again we ask for your assistance

For this event to SMOOTH on TIME and SAFELY we need a small group of volunteers (OFFICIALS) to help

out in 3 sections in the morning and 1 in the afternoon.

All Officials on the day will be supplied lunch and drinks.

An Officials breifing will be held before the drivers breifing. So all Officials will need to be at

the Shepparton DECA complex before 8am on Saturday.

Be aware NO DRIVERS BREIFING OR COMPERTITION will take place until all Officials positions have beed filled.

So if this sounds like you or 1 or more of your friends or family post up in here and i add you to my list.

Cheers

MORNING

SKIPPAN

Starter.. Wayne

Finisher.. Martin

Timer..

Spotter.. Josh _TypeX

MINI WANG

Starter.. Campbell

Finisher.. Keiran

Timer.. Lauren

LONG WANG

Starter.. Anna

Finisher.. Juliette

Timer..

Spotter.. Sam

Spotter.. Sachi

AFTERNOON

SKIDPAN

Starter.. Wayne

Finisher.. Martin

Finisher..

Timer..

Timer.. Keiran

Timer.. Anna

Link to comment
https://www.sau.com.au/forums/topic/389529-deca-volunteers/
Share on other sites

Is the spotter a timer? Lauren and I can help out in the morning. Chuck us together somewhere and give Lauren a seat.

I'll help out in the arvo too, but I think Lauren will want to go shopping.

spotters watch the cars go by and report if they hit a cone or WD (wrong direction)

finisher is usually the timer

both jobs are just as easy as eachother :thumbsup:

Link to comment
https://www.sau.com.au/forums/topic/389529-deca-volunteers/#findComment-6207533
Share on other sites

Guest
This topic is now closed to further replies.


  • Latest Posts

    • Hi. This is just my curiosity because iam sure the tuner figure something out...but either way i want to ask. The "problem" is that the Nistune ECU (Stagea FW and RB25DET NEO from Stagea) sees many times the speed than the speedo does(he says the speedo show 120 km/h - correct speed and the ECU shows like 510km/h ) I told him that this car/tranny getting speed from rear diff. If iam not mistaken the RB25DET NEO "need" to see tranny speed sensor? (my tranny has the plug for it). So couple of "question" If he connects/wire the speed sensor to the tranny...are the signals gonna intervene and if...what if he disconnects the rear diff one and the speedo stops working? Or the "new" sensor from the tranny "take over" and will not going need the one from diff? As i said i know he figure/get that done...iam just curious to know what are the solutions 🙂 
    • Your IACV is set to idle too low. You need to adjust it via the screw Duncan mentioned. From memory it should be 650rpm with the valve electrics unplugged. What is it trying to idle at with the IACV plugged in?
    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
×
×
  • Create New...