Jump to content
SAU Community

Recommended Posts

Item: Stripping 180sx

Location: Morayfield

Item Condition: Various

Reason for Selling: Stripping

Contact Details: Lucas 0403468079 SMS during work hours

Need get rid of shit asap, trying to sell house and I can’t be f**ked finishing it now and moving with it

Offers Welcome

Shell only comes with bits and pieces, not mentioned below. Quarter glass good, dark tint. Registerable shell with mod plate for compliance. Rear end has spare wheel tub cut out, replaced with sheetmetal, rear seam spot welded, raised strut tops 50mm or ultra low. Rear guards are cut to suit fenders, lh side bit rough but racecar . $600

S13 Complete SR20DET W/5speed box comes with loom and ecu , high flow turbo, high mount stainless manifold, external gate $2400.

Genuine Origin Streamline Bodykit perfect fit with foam in both bars , in gel coat expect front bar in matt black $1200 firm will keep for other 180 if it does sell.

Genuine Gcorp 40mm Gtr style fenders suit 180sx $400

Uras (monkey magic) 180sx front bar, cracked ziptied lip etc. $100

S13 Type X clear indicators $60

S13 Doors complete with glass less mirrors $60 each

180sx headlights with motors/plastic sourrounds $180pair

S13 Mirrors $50 pair

S13 NPG Jap brand Coilovers, pillow ball camber tops no leaks or knocks, just been chilling for a couple years. May need coat of paint to make pretty $550

Modified Rear S13 non hicas cradle, not quite finished, needs holes drilled for control arms in a couple places , and front bushes welded up, however it has pick up points raised 40mm. Braced with 2mm sheet in pick up points. Will give u 53mm roll centre correction when flush mounted to chassis. Most of the hard work done . $350

S13 4 stud knuckles, cut and shut for more lock. $250

CA18DET Brakes F+R calipers and rotors $140

4 pot z32 brakes and rotors $250

Front Sway bar $40

Cross member $80

180sx Tailgate with dark tinted glass. $300

180sx Tailights with centre garnish $80

S13 mild steel catbacl exhaust good for a beater $60

S13 Steering rack less boots $80

CA18DET Front seats, have harness hole $50 each

Rear seats $30

Rear Trims $60pair

Washer bottle $20

Dash with cracks $40

Passenger A pillar with handle trim $40

Fuel Tank with pump assy. $100

Seats belts $30 each

centre console $60

Aircon control face $50

hyrbid intercooler alloy pipe kit suit sr20 $200

probably more just ask

Link to comment
https://www.sau.com.au/forums/topic/390318-180sx-stripping/
Share on other sites

  • 1 month later...
  • 2 weeks later...

hi lucas, im after the following:

the interior mirror covers(triangles) both sides

the radio brakets

boot plastics

gear shifter boot

tail lights and centre piece

and the coilovers if available.

can i get prices sent to sydney 2756

pm me if you wish.

cheers, luke.

Link to comment
https://www.sau.com.au/forums/topic/390318-180sx-stripping/#findComment-6280996
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Dear folks My family members have 4 different cars : Triton 2015 and Corolla 2011 and Mazda3 2012 and Hyundai Elantra 2014 Looking to buy engine oil funnel spill free What I found are are below  https://www.amazon.com/gp/aw/d/B0BBTTJNKX?ref=ppx_pt2_mob_b_prod_image&th=1 https://www.ebay.com.au/itm/145553221359?srsltid=AfmBOoqYBU6Ptw0LU_bAp_k67U3qkF97HHvePkA7iHZw8vUmiwoIRaRr https://www.amazon.com/gp/product/B09X23TCS5?th=1 Is there a funnel with attachment that fits most cars ? Don't mind to spend for a decent quality  Thx  
    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
×
×
  • Create New...