Jump to content
SAU Community

Rota Grid Fitment On R33

sky017
 Share

Recommended Posts

32rrr Collaborator

32rrr

Posted
Posted

The most you want on the front is a 9" rim, 10's on the back. 18x9 +30 front and 18x10 +18 for the rears to stick out a bit and 18x10 +38 for them to sit flush

I highly recommend JDM concept for a decent set of jap wheels at a reasonable price.

the BEST thing you could do is go and check what size wheels and tyres they are that you have on there now and get out your tape messure to check were the wheels will sit using http://www.rimsntires.com/specspro.jsp which will tell you everything you need to know.

  • 1 month later...
FBRacing Rising Star

FBRacing

Posted
Posted

Are the Grids you are looking at the same as the Grid Drift that can be found at driftworks.com? On their site, there's a few different grid designs that they offer. My understanding is they start the drift wheel at 8.5 and wider.

  • 3 weeks later...
simpletool Mentor

simpletool

Posted
Posted (edited)

Depends on tyre size also.

ie. 18 x 10" +38 with 265/35/18 would be my choice for rear. If you want some rim poke you can drop the offset to 18-25 or so but you'll have to forgo tyre width down to 235/40 and put silly camber on and lose grip. Fine for a cafe racer.

Front I'd try to get something like 18 x 9" +25-30 with 235/40, or even 9.5" +22 if you want some poke (again you'll have to drop tyre to 225 or so and some guard rolling and remove inner liner).

Edited by simpletool

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      remote oil cooler hose size, 8,10 or an12?

      By MBS206 · Posted

      -10 is plenty for running to an oil cooler. When you look at oil feeds, like power steering feeds, they're much smaller, and then just a larger hose size to move volume in less pressure. No need for -12. Even on the race cars, like Duncans, and endurance cars, most of them are all running -10 and everything works perfectly fine, temps are under control, and there's no restrictions.
    • nouveau_poor
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By nouveau_poor · Posted

      Update: O2 sensor in my downpipe turned out to be faulty when I plugged in to the Haltech software. Was getting a "open circuit" warning. Tons of carbon buildup on it, probably from when I was running rich for a while before getting it corrected. Replaced with new unit and test drove again. The shuffle still happens, albeit far less now. I am not able to replicate it as reliably and it no longer happens at the same RPM levels as before. The only time I was able to hear it was in 5th going uphill and another time in 5th where there was no noticeable incline but applying more throttle first sped it up and then cleared it. Then once in 4th when I slightly lifted the throttle going over a bump but cleared right after. My understanding is that with the O2 sensor out, the ECU relies entirely on the MAP tune and isn't able to make its small adjustments based on the sensors reading. All in all, a big improvement, though not the silver bullet. Will try validating the actuators are set up correctly, and potentially setting up shop time to tune the boost controller on closed loop rather than the open loop it is set to now. Think if it's set up on closed loop to take the O2 reading, that should deal with these last bits. Will try to update again as I go. 
    • Dose Pipe Sutututu
      remote oil cooler hose size, 8,10 or an12?

      By Dose Pipe Sutututu · Posted

      More so GReddy oil relocation kits, sandwich plates, etc. all use 10AN fittings. And same, I've only used 10AN and my car sees track work (circuit, doing laps, not 10 sec squirt business).
    • Duncan
      remote oil cooler hose size, 8,10 or an12?

      By Duncan · Posted

      Dunno. I run -10 on the race car.
    • GD51LA
      remote oil cooler hose size, 8,10 or an12?

      By GD51LA · Posted

      street use or race track, what hose size and why? what factors change with the hose size options ?   see most comon is an10. when you see most oem external coolers are closer to an12? does high volume oil pump like nitto need an12 or 10 be just fine
×
×
  • Create New...