Jump to content
SAU Community

Rb30/26 Engine Parts And Accessories

Power Glide GTR
 Share

Recommended Posts

Power Glide GTR Contributor

Power Glide GTR

Posted
Posted

Selling RB26 ported cylinder head with Tomie pro cams 290 11.5 Tomie springs and retainers ported by Competition Engines comes complete with 1000cc rochester injectors custom billet fuel rail adjustable cam gears intake manifold rocker covers and valley cover HIGH MOUNT twin turbo steam pipe exaust manifolds ( ARP HEAD STUDS GTR THREAD brand new never used ) under 1500km $3700.00 ONO

Rb30 crank carrillo rods and SPS 86.5mm piston witth 22mm pins suit rb 30/26 head Under 1500km $2200.00 ONO

Rb30 russell high volume sump suit external oil pump single stage $550.00 ONO

External oil pump single stage with brackets pulleys remote filter set up oil lines $1700.00 ONO

Autronic SMC self tune with wiring loom $1100.00 ONO

If interested Call or sms on 0408 719 873

Cheers Tas

Link to comment
https://www.sau.com.au/forums/topic/391746-rb3026-engine-parts-and-accessories/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Dose Pipe Sutututu
      Why am I hitting a power wall with my stroked RB25?

      By Dose Pipe Sutututu · Posted

      Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • MBS206
      RB25DET with solid lifters - which cams ?

      By MBS206 · Posted

      Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • MBS206
      NC MX5

      By MBS206 · Posted

      They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...