Jump to content
SAU Community

Rb25 Cam Cap Buggered

SYK-200

By SYK-200,
in Engines & Forced Induction

 Share

Recommended Posts

SYK-200 Enthusiast

SYK-200

Posted
Posted

Hello everyone...again! a few months ago i built a rb25, and ever since it was running their was a really high pitch squeal coming from the engine and i had no clue wat it was until yesturday i took off the cam covers and found metal shavings at the first cam cap, so i took it off, and what do i find? the cam cap and camshaft have been worn VERY badly, wat can cause this? no oil getting to it? over tightening the bolts? i didnt install the cams, we sent it to our local machine shop and got the block/head cleaned up, also installed tomei valve springs. ill post up a picture so you can all see how bad it is...

post-74114-0-58401200-1329458772_thumb.jpg

post-74114-0-89122200-1329458800_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/392073-rb25-cam-cap-buggered/
Share on other sites
rob82 Mentor

rob82

Posted
Posted (edited)

From those phots it appears to be Abrasive wear which is probably due to lack of sufficient lubrication. It seams weird that it etched the middle of the cam bearing surface away. My guess is they possibly tunnel bored the cam bore and forgot to debur the oil feed cause both a blockage of the oil passage and significantly higher loading on the middle section of the cam journal. Really hard to tell just from those photos.

Edited by rob82
JonnoHR31 Grand Master

JonnoHR31

Posted
Posted

did they do any machining? was it the original cap from that engine installed on the correct side? if so lack of oil is the only reason for that to happen, but to get that bad it must have been getting no oil whatsoever. what does the oil feed look like?

The Dan Grand Master

The Dan

Posted
Posted

If you put the cap on the wrong side and the top half overlaps the bottom half on the leading side, it will start removing material from the cap as it rotates. The removed material will just stay there, stuck in the middle and continuing to wear the cam away like a big clump of camf*ck

SYK-200 Enthusiast

SYK-200

Posted
  • Author
Posted

at JONNOHR31, i dont exactly know what they machined, my brother got the machining work, the engine was my school project for HSC, i built most of it, brother payed for it all...

at abr33, we first started the engine in around july 2011, and since 16th feb, it probably has only been started ~15 times.

is this at all repairable, or a new head is needed now? definately a new cam is needed lol, on the positive side, at least i found this problem before something worse happened!

abr33 Proficient

abr33

Posted
Posted

Repairable? maybe, get a competent shop to weld your busted journal and tunnel bore it back out.

Or if its easier get a new head, your lucky you didnt break your cam and eat your engine worship.gif

Would be a tricky one to repair

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Murray_Calavera
      Quieter performance exhausts (or muffler add-on options)

      By Murray_Calavera · Posted

      Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • f00stx
      Quieter performance exhausts (or muffler add-on options)

      By f00stx · Posted

      So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...