Jump to content
SAU Community

A31 Cefiro For Sale

D K C

By D K C,
in Cefiro Parts Classifieds

 Share

Recommended Posts

D K C Enthusiast

D K C

Posted
Posted

Have my Cefiro up for grabs, currently unregistered as rego has lapsed.

List bad points prior to sale: Auto, valve stem seals require replacement down the track ( occasional puff of smoke on idle )

List of good points: can be registered, is entirely intact, straight body ( all on colour ) mint interior ( no cracked dash or torn trims ) I have all the parts required to perform manual conversion bar clutch, would make a great track base for anyone wanting to get into drift.

Model: 1988 A31 Cefiro

Colour: Pearl white

Engine: RB20DET

Trans: Auto

Mods:

Engine:

Full jap stainless 3 inch exhaust

High flowed RB25 turbo

Front mount cooler with custom stainless piping ( does not cross over rocker covers )

K&N filter with hard intake pipe

Custom stainless catch can ( mounted on firewall )

Boost controller bleed valve

Neatened up wiring and vac line layout

Fuel system:

Bosch 044 mounted in tank

Tomei type S reg with gauge

Wheels/Steering/Suspension/brakes:

Full tein HR adjustable coilovers

5 stud conversion consisting of R33 rear and S14 front with s14 lower control arms

Stock r33 wheels

Non hicas rear end

Non hicas steering rack

R33 power steering pump

R33 power steering reservoir

Upgraded thicker front sway bar

Front strut brace

Body:

Pearl white

Standard body

Series one lights with front covers removed to give ' unique ' look

Spoilers holes removed from boot professionally

Series 3 front bar lip flipped and fitted to series one bar to give ' unique ' look also

Interior:

"MINT"

Blitz boost gauge

Foot park brake to centre handbrake conversion

Old school nardi wheel

R33 centre console conversion

Full Cefiro factory floor mats in A1 condition

Fuel cut off switch ( paranoid about car theft )

Car has been serviced within the last 20kms including oil, coolant, plugs, fuel filter and powersteering oil.

Unable to load photos at current time but will happily mms them across.

Asking $5500 ONO with all manual conversion gear included. ( box, pedals, drive shaft, master cylinder and lines )

0431 197 087

Located in west aus

As stated price is ONO dont be afraid to offer something

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Orza81
      1993 TH1 Blue R32 Skyline GTR VSpec

      By Orza81 · Posted

      Hi SAU community  Wondering what my 93 Very RARE TH1 Blue R32 GTR VSpec is worth these days?? Build is fairly dated now All Mods are Compliance Approved  Runs RB26 done only 10000ks Greddy T88 done only 8000ks HKS Cam 1000cc Injectors Full Titanium Exhaust Nismo Intercooler Nismo Oil Cooler HKS Oil sump Tein Super Street Coils Cusco Sway Bars RAYS TE37 19x10.5 DYNO street tune makes around 700hp on 98octane  
    • r34.rory
      Hazards not working R34 GTT

      By r34.rory · Posted

      It does sound like a fuse considering the indicators work..I’ll triple check when I’m free and report back.    thanks for the reply.
    • JC71
      98 ER34 GTT idle races, if AAC is unplugged, then idles perfect

      By JC71 · Posted

      no, the car was a manual 5 speed from the factory and still is.
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      While going through data logs late last week, I spotted a small issue with my WMI. My WMI starts to progressively inject at 11psi of boost. I'm using a 25psi cut in pressure switch on my WMI as an added safety and if the curve is linear, I should hit that 25psi on my WMI system around 13-14psi of boost.  As per my data logs, my WMI pressure switch only activates around 19psi of boost. This is causing my non WMI 4D map to trim for WMI. I'm presuming this is caused by the mechanical switch response time, injection curve not being linear or both.  I ordered a 2-10psi adjustable cut in pressure switch which should correct this. If this doesn't resolve it before my dyno appointment on Friday, I'll just remove the pressure switch temporarily and more than likely replace it with a pressure transmitter afterwards.    BTW Speedtek has yet to refund me.
    • Sean'O
      3D printing fun

      By Sean'O · Posted

      Yep PETG (Polyethylene terephthalate glycol), my 'go to' plastic, printed to precisely how long I wanted 🙂, about a finger length ha ha. I would usually grind up something but since I've got the printer I thought I might give it a try and it worked beautifully ^_^b So with regards to torque, there's a little bit of science behind the orientation of the print, fill density, fill pattern and number of external perimeters which can increase the strength dramatically, but you still need to work within the constraints of the material and the orientation of the model for sure. I certainly wouldn't be making a breaker bar out of plastic, but this little bugger is very strong for it's size that's for sure.
×
×
  • Create New...