Jump to content
SAU Community

Recommended Posts

Rear Arms

$50 ea for the lowers

$30 ea for the uppers

th_affbdfe9.jpg

Superspark RB25DET-S2 coilpacks

$250 inc post

th_image-1.jpg

R33 GTST LHS Door, KR4 colour. With glass, with motor, no card, no switch, no mirror. Paint in good cond, some clear coming off in one spot.

$180

R33 GTST RHS Door, KR4 colour. With glass, with motor, no card, no switch, no mirror. Prefect condition.

$240

Have the same thing in QM1 white. With glass, with motor, no card, no switch, no mirror, prefect condition.

$240

th_11092011424.jpg

th_11092011416.jpg

Bootlid gas struts and hinges, could mod the struts for bonnet if you wanted.

$50 inc post

th_01112011565.jpg

R33 GTST intake snorkel

$35 inc post

th_01112011563.jpg

R33 GTST front upper arms, perfect condition (have cusco's don't need these)

$55ea, $100 for both

th_01112011562.jpg

R33 GTST side winker (indicator, lol), these will fit S1 and S2.

$20 inc post

th_01112011569.jpg

R33 GTST 4 piston sumitomo stock front brake calipers (only the fronts)

$250

th_DSC_1018.jpg

HKS SSQ BOV, this is a real SSQ not an ebay special that says it's an SSQ but will leak within seconds.

$80 inc post

th_24102011524.jpg

Sub box with amp and speakers, fits in a R33 boot

$100

th_01112011550.jpg

R33 GTST S2 pink label AFM, POD

$40 + post

th_01112011554.jpg

R33 stock cast intake + BOV

$65 + post

th_01112011555.jpg

SRI 15mm - M12 x P1.5 (5 x 114.3)

$85 includes shipping

th_e1a3b51d.jpg

Link to comment
https://www.sau.com.au/forums/topic/393061-r33-gtst-parts/
Share on other sites

Location keen on brakes and coilpacks

Vic

Can meet you at Garage Cafe in Carlton on the 21st at the SAU VIC meet

ill grab the bov today if ya could do it for $50 ill come pick it up??

Can do $80 posted.

Link to comment
https://www.sau.com.au/forums/topic/393061-r33-gtst-parts/#findComment-6273390
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...