Jump to content
SAU Community

Recommended Posts

EOI

Basically, thinking of stripping my r33, there are a lot of parts, aftermarket and standard. I will list some of the major items and if anyone is interested please PM me and if I get enough interest I think ill let the memories go and start pulling it apart. The car was never completed, everything is mostly bolted on however never started or tuned as I started working a lot and the whole project went out the window. Now I'm trying to move up with my career and just don't have the time for it anymore.

I am open to offers on all parts.

rb25det s1 motor, complete minus turbo/manifold etc, compression 145-160 on all 6 cylinders - $1500

(made 194.6kw with std. turbo on 12psi with full exhaust and intercooler so very healthy)

rb25det s2 gearbox 86,000kms on it - $1500 or as a manual conversion kit $2000 (everything you need)

HKS GT2835r turbo (420hp rated, seen couple track days since rebuild made 290rwkw on another car) kit including HKS cast manifold, Greddy ext. gate, screamer pipe, dump pipe, steel braided lines, turbo intake and hot+cold side piping in lobster back stainless steel by AM Performance - $2200

AM Performance cat back exhaust system 2x2.5" in to 2x4" pipe with titanium tips - $900

VQ35 ecu with rb25 nisstune board (lets you use vct unlike RB20 ecu)- $450

Yellow Jackets coilpacks for s1 rb25 (all working, used for 1 year, fantastic coilpack, search forums) - $250

Power Enterprise 850cc side feed injectors to suit rb25 in rail, brand new - $750

ORC Single plate clutch, 409 series unsprung center, used for 6months still in good cond - $400

Greddy copy plenum kit (rb25 throttle body adapter, nipple fittings, hose fittings, hoses) brand new - $350

External fuel pump setup, 2L tank + bosch 044 with mount and all fittings + ethanol fuel hose, brand new - $350

Wlabro 550hp intank pump - $100

R33 Non-sunroof 9point cusco D1 cage, through dash with side intrusion bars and padding - $950

R33 brake setup, hubs, slotted discs, calipers, a1rm pads and adr approved braided line - $800

R33 BC BR Coilovers, used for 4000kms, like new - $900

R200 locked diff, tight as - $200

Kazama castor arms suit r33 and other models - $150

Rear camber arms unknown brand, brand new - $100

Hicas lock bar - $80

R32 genuine GTR intercooler - 150

Rb20/25 hybrid intercooler kit, core is rough but no leaks - $150

z32 afm with plug - $150

q45 afm - $80

Work VS-XX wheels, 18x10 +13 front with kumho ku36 tyres 60%, 18x12 -4 rears with bridgestone tyres 40%, not for groupies or wanna be's... need some serious guard work to fit these babies. Genuine 3 piece - $3000

And everything else that you could think of, suspension arms, lights, dash pieces, trims, looms etc etc... im sure I missed a lot of little aftermarket things but those are the major ones listed. If I go ahead with it I will list all the parts and pictures as its taken apart.

Also, clean registrable r33 shell/plates.

If youre interested in anything PM me, when I have enough interest the strip show starts.

Edited by SkyHi_33
Link to comment
https://www.sau.com.au/forums/topic/394832-eoi-stripping-300kw-r33-gtst/
Share on other sites

No std. steering wheel, ive got a momo drifting suede deep dish, and two no brand deep dish suede wheels, one black one blue.

Haha its a very nice exhaust, $1550 from memmory new and its barely been used!!!

Ps. Cant reply to pm's off the phone sorry guys, ill get to it asap!

Thanks :)

I can get pics of most of the items, the plenum is brand new. Ill wait a few days till Ive got enough interest and if there is, then Ill post another for sale thread with all the pictures of parts.

Im located in Adelaide, SA. Marion area. The shell is in primer and needs a bit of body work but its straight.

Steering wheels, I dont want to sell the momo just yet but the other two I can do for $80ea + postage, theyre brand new in the box still.

they look like this (same wheel on a mates car)

http://s2.photobucket.com/albums/y33/kfsRule_2/?action=view&current=steeringwheel.jpg

Edited by SkyHi_33

I havent got any pictures of most of the stuff atm, still deciding if I want to part it out. Have had a fair bit of interest so at this point I most likely will.

The rear arms are adjustable, and yes still got the engine loom.

As I said, Ill leave the thread up for a week or so, I've written down everyone's usernames for people interested in parts and will PM you in a few days when I figure out what to do with the car. In the meantime Ill try get a few pictures :)

Thanks!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
×
×
  • Create New...