Jump to content
SAU Community

Recommended Posts

Sig'd.

OT.

Patiently waiting for pics

Bugger, I wish I'd included the word "up" now.

Not sure how they'll help; but they can't possibly hurt.

Pics of push up bra; as requested.

wonderbra-full-effect-push-up-bh-schwarz-800x1157-1.jpg

cindy-push-up-bra-1076304753-500x700.jpg

You're welcome.

  • 2 weeks later...

Ok here it is. "Stagline" Only one that i know of. No build thread, if you wanna know about it PM me. (Not being selfish).

oh and to the haters on this forum who said it wont happen and various other things, i bet you feel bad now that its done and actually followed through (you know who you are)

It is a bit rough, panels need to be lined up, panels are a bit rough but have no damage and wiring up the side blinkers but other than that it works.

post-88192-0-48079700-1348047098_thumb.jpg

post-88192-0-65026600-1348047141_thumb.jpg

Big thanks to the following people/businessess.

-Daleo for the front bumper.

-Scotty for the grill.

-Chadsta for the headlights and Radiator support.

-Nisswreck For the Gaurds, Bonnet and Blinkers.

-Brent for the photos that you see.

-Matt for helping me put it on.

Am i one of you stagean people now?

hahahha Enjoy!

Edited by Howaitonaito

finally a f#$king V35 that looks good!

Spray Grill black leaving Nissan Badge Silver

Open and spray up the inside of the headlights

Eyelids

FTW!

Flares + wing! :whistling:

different wheels with a decent 40+ profile

Edited by Jetwreck

finally a f#$king V35 that looks good!

Spray Grill black leaving Nissan Badge Silver

Open and spray up the inside of the headlights

Eyelids

FTW!

+1 for everything Jetwreck said!

Well done mate!

Just see if you can lower that D/S bonnet rubber mount at the front a little bit to make that panel fit nice along the top of the headlight.

:thumbsup:

http://www.skylinesaustralia.com/forums/topic/409637-wrecking-series-1-nm35-stagea-or-may-sell-complete/

*Cough* Drivetrain conversion...*cough*

i was going to do flares but it would have been a fortune to have customized for the rear arch/door area and what not. Getting the holes filled up from where the body moulding was and having it all lined up and painted and got something special coming from japan; JP simple front lip, unpainted so it blends in with sideskirts.

funny thing is all the lights are opposite my blinkers where my highbeams would usually be on a stag and when i put my high beams on they came up orange!!! but i fixed that earlier.

the radiator mount is about 2/3inches shorter than the V35s one so it doesnt line up where the old one did so the bonnet hits on it so the mount has to be trimmed.

other than that im chuffed with it, gets the looks from people.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...