Jump to content
SAU Community

R33 Rear Window

UWISSH!

By UWISSH!,
in Exterior & Interior Styling

 Share

Recommended Posts

UWISSH! Grand Master

UWISSH!

Posted
Posted

seeing as my r33 isnt my daily anymore i can finally start taking some parts off it.

i want to remove the rear window wiper.

How big is the hole in the rear window? as im going to order a plug to fill the hole, ive tried searching but nothing came up that helped

Link to comment
https://www.sau.com.au/forums/topic/396484-r33-rear-window/
Share on other sites
PSI Parts Veteran

PSI Parts

Posted
Posted

I'm in the same boat as you and did this a few weeks ago. The large hole is 29.62mm.

I'm going to use the hole to put in a Battery Kill Switch as its both easy access to the battery and good location that is easily identifiable. I've used the smaller hole on the right for a GPS sensor that sits on the out side of the window and run the cable inside the cabin that goes to the Racepak dash.

Link to comment
https://www.sau.com.au/forums/topic/396484-r33-rear-window/#findComment-6298044
Share on other sites
PSI Parts Veteran

PSI Parts

Posted
Posted

It's very simple. Remove the cover from the rear windscreen bolt on the base of the arm, undo that and then it's just a matter of a few other smaller bolts and you are done. Once you have a look at it, you will be fine in taking it off.

Link to comment
https://www.sau.com.au/forums/topic/396484-r33-rear-window/#findComment-6299107
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...