Jump to content
SAU Community

R33 Rear Window

UWISSH!

By UWISSH!,
in Exterior & Interior Styling

 Share

Recommended Posts

UWISSH! Grand Master

UWISSH!

Posted
Posted

seeing as my r33 isnt my daily anymore i can finally start taking some parts off it.

i want to remove the rear window wiper.

How big is the hole in the rear window? as im going to order a plug to fill the hole, ive tried searching but nothing came up that helped

Link to comment
https://www.sau.com.au/forums/topic/396484-r33-rear-window/
Share on other sites
PSI Parts Veteran

PSI Parts

Posted
Posted

I'm in the same boat as you and did this a few weeks ago. The large hole is 29.62mm.

I'm going to use the hole to put in a Battery Kill Switch as its both easy access to the battery and good location that is easily identifiable. I've used the smaller hole on the right for a GPS sensor that sits on the out side of the window and run the cable inside the cabin that goes to the Racepak dash.

Link to comment
https://www.sau.com.au/forums/topic/396484-r33-rear-window/#findComment-6298044
Share on other sites
PSI Parts Veteran

PSI Parts

Posted
Posted

It's very simple. Remove the cover from the rear windscreen bolt on the base of the arm, undo that and then it's just a matter of a few other smaller bolts and you are done. Once you have a look at it, you will be fine in taking it off.

Link to comment
https://www.sau.com.au/forums/topic/396484-r33-rear-window/#findComment-6299107
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • WMDC35
      Wheel Sizes & Offsets For Skylines

      By WMDC35 · Posted

      A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Duncan
      RB20DE NEO smallbox clutch.

      By Duncan · Posted

      Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
×
×
  • Create New...