Jump to content
SAU Community

Braided Hoses

Anfanee

By Anfanee,
in Australian Capital Territory

 Share

Recommended Posts

D.I.Y. Mik Veteran

D.I.Y. Mik

Posted
Posted

The two places i know of ( i havent looked much) are Enzed and Aushose, they have those speedflow fittings and all that anodized stuff for braided hose.

Revolution racegear have lots of heat insulating sleeves and things you wont find anywhere else.

I always use the phonebook cos one place probably wont have all the things you want.

I hate driving around fyshwick for an hour looking for one little thing.

good luck finding all of it, it can be a real pain getting all the little bits together, i noticed you can get kits for GTRs but not GTSTs (dammit!) on the net.

Link to comment
https://www.sau.com.au/forums/topic/396584-braided-hoses/#findComment-6298723
Share on other sites
sweefu Mentor

sweefu

Posted
Posted

The guy who runs the Enzed in Fyshwick is a bit of a cock, and overpriced even for speedflow. If I were you I would order the speedflow fittings from eBay and the braided hose etc then make your own. If you want a shop in Canberra though, I have bought a couple of fittings from Pirtek in Fyshwick, prices were reasonable and service is good.

I also agree with DIY Mik above, GTR's will be more difficult to get the fittings for, I have a stock set of R32 GTR lines here and they are a bit odd.

Link to comment
https://www.sau.com.au/forums/topic/396584-braided-hoses/#findComment-6298731
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • albyz34gt
      34 de+t conversion using s2 stagea automatic transmission, engine harness and ecu

      By albyz34gt · Posted

      Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Duncan
      R32 GTS (RB20DE) Injectors Replacement

      By Duncan · Posted

      Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • GTSBoy
      Wheel Sizes & Offsets For Skylines

      By GTSBoy · Posted

      There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
×
×
  • Create New...