Jump to content
SAU Community

Recommended Posts

Hi,

I am regrettably selling my GTR because of already having another car.

I am the third owner of the car since imported from japan and have spent a lot of time and effort to get it to its current state.

Some of the mods that have been done on the car since I've owned it include:

-Rebuilt motor (still under 10,000km since it being rebuilt)

-Wiseco forged pistons

-Nitto Rods

-Brand new R34 GTR crank

-New R33 N1 turbos when rebuilt

-Trust Ti cat back exhaust

-Aftermarket front pipes

-High Flow cat

-Adjustable Cam gears

-JJR coilpacks

-Tein Super Street coilovers (Aus spec) (Less than 5000km)

-Upper arm bushes are off set to give it a slight camber

-New tyres (Kumho Ku31)

-R34 GTR rims

-Trust Strut Brace

-Arc Titanium Radiator Shroud

-New battery

-HKS boost gauge

-Aftermarket radiator

-Sub and Amp

I've been told that the color isn't the factory black and actually has more of a pearl in it.

The car is hardly driven and always parked inside the garage.

Price: $21,000

If you have any questions about that car don't hesitate to message me or call me (after 6pm) as I am sure that I have forgotten to mention things.

Car comes with a lot of spare part such as another exhaust to pass EPA, another 3inch cat back exhaust, 2 set of coilovers, and another front lip.

Woody 0401530960

2011-12-08192711.jpg

2011-12-08192654.jpg

2011-12-08192738.jpg

2012-04-04171951.jpg

2012-04-04172044.jpg

2012-04-04172053.jpg

Edited by El_Mutto
Link to comment
https://www.sau.com.au/forums/topic/396944-vic-r32-gtr/
Share on other sites

Looked through the receipts of when the engine was rebuilt and found that it also had a Tomei Sump Baffle, N1 oil pump, and an N1 Water Pump installed when rebuilt.

Link to comment
https://www.sau.com.au/forums/topic/396944-vic-r32-gtr/#findComment-6306791
Share on other sites

Thanks for all the nice comments!

Should of mentioned this in the original post the car comes with a Apexi Power FC and has 102xxx on the clock.

The price is negotiable but please no lowballers.

Link to comment
https://www.sau.com.au/forums/topic/396944-vic-r32-gtr/#findComment-6315007
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...