Jump to content
SAU Community

Recommended Posts

Wanna go back to the drags but only got chinese tyres which also are old n hard.

But need some new tyres, better quality an newer, was considering some KU36's.

first time i went to willowbank ran some falken 452's an managed a best of 1.59 60ft. would ku36's give better traction? Problem i can see is i dont know how to warm the tyres, so would cold ku36's be any grippier then falken 452's?

as i noticed last time as it got latter in the nite n cooler my 60ft times were slowly getting worse, tho mph was goin up so the times stayed the same (11.7)

also is there an easy way to warm ur tyres in an 33gtr?

any experience or advice/tips would be greatly appreaciated =)

Link to comment
https://www.sau.com.au/forums/topic/397038-tyres-for-dragstreet/
Share on other sites

If it's a relatively stock GTR - 1.60 for street tyres is pretty reasonable. You'd struggle to get much better on street tyres, maybe 1.5. Tyres aren't 'as important' as you don't really have the power to turn them (if its stock-ish).

No easy way on a R33 GTR to warm tyres, just drop the pressures down to around 20-22psi, avoid the wet ground for burnout start and away you go.

Has 420hp atw (think thats bit over 300kwatw) about 40hp more then when i was there the first time, seen a couple gtr's one with bout 320hpatw an one with 460hp that couldnt get traction first i think had pretty cheap rubber but the 460hp one had fairly mid range 265 rubber (cant remember brand) an couldnt get traction till 2nd gear an started to brake traction again an only managed a 12.4 maybe 12.3

just know every 1/10of a second off the 60ft is worth a fair bit more at the end... tho my original goal was to crack 200km/h at the end of the strip, 60ft might not count much towards that (top speed so far was 189km/h @ 380hp atw)

tho a quick 1/4 mile slip quietens the supercharged commordore boys kw bragging! :rofl:

yer i always went around the water, but there was a definate change in 60ft times as the air got cooler, an the tryes cooled down, first runs tyres were still a lil warm from driving there, latter runs the car had been sitting still for a fair while.

so do u think ku36's or a simalar tyre would get beta grip when cold then a normal street tyre?, plz recommend a different tyre if u think they're beta, but the tyres need to be drivin on the street, on a daily basis so dont want "drag" only tyres. i guess i could put it into limp mode.. but would be a lil annoying tho would be worth a go...

  • 9 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Lamb roast on Saturday will be different 🥲
    • They are under bucket shims. Tomei provides a test shim kit and then any measurement of shim required. 
    • I always wondered how you were supposed to buy a set of 24 buckets and somehow magically have every single one of them yield exactly the desired clearance. I would have thought you'd need to assemble a cam with either 12 "sample" or "example" buckets of known top thickness (or a single such sample/example 12 times over!!) measure clearances at every valve, and then do the usual math to work out what the actual "shimness" of each bucket needed to be, before buying the required buckets to make up he thicknesses that you didn't have on hand.
    • I now seem to be limited in power due to my rev limit/hydraulic lifters in my built RB25. I'm looking into converting over to Tomei solid lifters. Question for anyone that has done the conversion. I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  I don't know where I got this idea, as so far I see no mention of this in any of the Tomei documentation. It just states I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
    • I couldn't agree more. I should have started from the get-go with a NEO or solid bucket conversion. I started looking into converting over to solid lifters yesterday. Now for some reason I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  But I see no mention of this on any of the Tomei documentation. It just states that I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
×
×
  • Create New...