Jump to content
SAU Community

Recommended Posts

  • Replies 55
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Just a little input, I had -5s on my rb26 on pump and full boost was at 5100 rpms. For track it was USELESS, for straight roads though it was marvelous!

To make the -5s work, you really need to build the engine such as Piggaz which I've been in before but you have to build it correctly. I've also been in RS's with a standard 26 and you will notice the difference but again, either build the engine to suit the turbos, or pick the turbo to your engine.

Again, I will just repeat what the others have already stated, E85 vs pump fuel is VERY different.

Also, -9s may have good response but they run out of puff if you want start to aim for more power where as the -5s will be able to go a little further.

I would say you have a few decisions to make before you make your choices (E85 or pump, 26 or stroker +, purpose of car, power vs response, etc).

Just a little input, I had -5s on my rb26 on pump and full boost was at 5100 rpms. For track it was USELESS, for straight roads though it was marvelous!

To make the -5s work, you really need to build the engine such as Piggaz which I've been in before but you have to build it correctly. I've also been in RS's with a standard 26 and you will notice the difference but again, either build the engine to suit the turbos, or pick the turbo to your engine.

Again, I will just repeat what the others have already stated, E85 vs pump fuel is VERY different.

Also, -9s may have good response but they run out of puff if you want start to aim for more power where as the -5s will be able to go a little further.

I would say you have a few decisions to make before you make your choices (E85 or pump, 26 or stroker +, purpose of car, power vs response, etc).

was there much get up and go before 5k? or you really had to wait for it? Then again, Once your at 5k, anther 2.5k and its pretty much next gear...Then youve got to build up to that again....

As good as the -5s sounds with the added power, And added room for more things in the future. Its really not going to be used to there full potential.

Going to buy the -9s!! f**k it. worst comes to worst i can sell and upgrade.

was there much get up and go before 5k? or you really had to wait for it? Then again, Once your at 5k, anther 2.5k and its pretty much next gear...Then youve got to build up to that again....

As good as the -5s sounds with the added power, And added room for more things in the future. Its really not going to be used to there full potential.

Going to buy the -9s!! f**k it. worst comes to worst i can sell and upgrade.

Well I'm in a 34 so I still have 4k left to go before next gear haha but I never dropped out of boost. Once it was on, it was ON!!! On my setup, it started to build around 3800rpms so anything under that was a little boring. My old R33 GTR had -7s and I thought that was a really good setup, managed 320kws and the response was excellent. Perfect for track conditions but being such small turbos, they ran out of puff top end. I believe GTRSean has -9s which I've also been in and those were great turbos too. I do believe Levinboy has them too and his produced pretty good results.

2.6 = SS's/-9's. Without a big dollar head and setup.

2.8 and bigger = -5's.

It's that simple, unless you're a nuckle dragger 'drag racer' that likes 'peaky power' which feels quicker.... Then they get smashed around twisties by a car that has 100 KW less peak figure.

Average power will belt peaky power every time AND be easier to drive.

Well I'm in a 34 so I still have 4k left to go before next gear haha but I never dropped out of boost. Once it was on, it was ON!!! On my setup, it started to build around 3800rpms so anything under that was a little boring. My old R33 GTR had -7s and I thought that was a really good setup, managed 320kws and the response was excellent. Perfect for track conditions but being such small turbos, they ran out of puff top end. I believe GTRSean has -9s which I've also been in and those were great turbos too. I do believe Levinboy has them too and his produced pretty good results.

hmm didnet know the 34gtr had a Bigger RPM limit? then the other rb26's

I dont get how a turbo such as the -9 can really run out of puff though, Dropping a little boost toward the top end i undderstand. But from feeling the way levinboy's pulled it was not running out at all. And once it drops out of the sweet spot, You would just go next gear. Seems pointless sitting above 8k if its not needed. But as you said, On the bigger blowers it is

2.6 = SS's/-9's. Without a big dollar head and setup.

2.8 and bigger = -5's.

It's that simple, unless you're a nuckle dragger 'drag racer' that likes 'peaky power' which feels quicker.... Then they get smashed around twisties by a car that has 100 KW less peak figure.

Average power will belt peaky power every time AND be easier to drive.

yer, Although my motor is built. Its nothing to write home about. Sure it will bring some reliability and piece of mind.( fingers crossed) its not something i really want to be sitting at redline to get a bit of power.

-9s it is.

i should almost stay off here till i pay for them so my mind is not swayed once again :)

2.6 = SS's/-9's. Without a big dollar head and setup.

2.8 and bigger = -5's.

It's that simple, unless you're a nuckle dragger 'drag racer' that likes 'peaky power' which feels quicker.... Then they get smashed around twisties by a car that has 100 KW less peak figure.

Average power will belt peaky power every time AND be easier to drive.

Even a Car with a big midrange and 30-40kws less peak will be quicker at the drag strip, unless you have a dog box/auto with short close gearing to keep it in the power

hmm didnet know the 34gtr had a Bigger RPM limit? then the other rb26's

I dont get how a turbo such as the -9 can really run out of puff though, Dropping a little boost toward the top end i undderstand. But from feeling the way levinboy's pulled it was not running out at all. And once it drops out of the sweet spot, You would just go next gear. Seems pointless sitting above 8k if its not needed. But as you said, On the bigger blowers it is

I said the -7s... not -9s :D

You will not be disappointed with the -9s until the power bug hits and you want more haha

Even a Car with a big midrange and 30-40kws less peak will be quicker at the drag strip, unless you have a dog box/auto with short close gearing to keep it in the power

That's what I said man.

Area under the curve. Peak numbers are pub talk!

Im expressing the fact,

Once you start on the road for power, you will always want more power. You get used to the power curve, and seeing as we all are adrenaline junkies, I want MOAR!!! haha.

But no Im not bored, I love it.

Wait till you hit the track then you will want bigger brakes!! And more suspension components hahaha

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...