Jump to content
SAU Community

Recommended Posts

hey guys pretty much as the topic states started gettin a weird clunk noise when i go over a bum from the from left (passenger) side no idea what it is also when i went to undo the wheels to have a look what the problem could be i noticed that when i put the ratchet on to undo the wheel i could actually move the wheel a bit (from left to right) with a bit of force really got no idea what it could be anyone got any ideas?

hey guys pretty much as the topic states started gettin a weird clunk noise when i go over a bum from the from left (passenger) side no idea what it is also when i went to undo the wheels to have a look what the problem could be i noticed that when i put the ratchet on to undo the wheel i could actually move the wheel a bit (from left to right) with a bit of force really got no idea what it could be anyone got any ideas?

Get the wheel off & keep looking, with some leverage, something is really faarkt. But you already know that.

Cheers GW :miner:

yeh i was thinkin something along the lines of ball joints or maybe tie rod ... question is how to check it ? or should i just take it to a mechanic?

You said "when i put the ratchet on to undo the wheel i could actually move the wheel a bit (from left to right) with a bit of force"

I said "Get the wheel off & keep looking, with some leverage".

What I mean is get further in, front end on axle stands, wheels chocked, car in gear, hand brake on, offending wheel off, head down, crowbar/piece of pipe/jemmy bar/tyre lever/something that you can work the wheel hub & linkages up down side to side with while you have a good clear view of what is going on or trying to come off, is loose or rooted, whatever. Could be lucky & have some nuts/bolts that just need tightening up. After you have determined that the strut is not about to colapse or some other nightmare, then arrange taking it to a mechanic if you cannot fix it yourself.

My other 2c.

GW :miner:

...i could actually move the wheel a bit (from left to right) with a bit of force really got no idea what it could be anyone got any ideas?

That would usually be a wheel bearing. Try moving the wheel top to bottom - if you get the same sort of movement, then it will almost certainly be the wheel bearing. Might just need a bit of grease and a tighten up. Might be shot.

Yeah. Usually if it's making a clunking noise, or some really weird grinding combined with squeaking sound when traveling over speed bumps, or just a general imperfection in the road, it will most likely be what the guys above outlined. Although, you only really notice it at slow speeds and the faster you go, you won't be able to hear it.

Get in there and see what it could be, if it's fixable... do it yourself or if you're not confident, just get a Mechanic to look at it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...