Jump to content
SAU Community

Recommended Posts

Hi

Can someone please explain what my oil pressure gauge is telling me.

I have a 95 R33 GTST which I recently took to a track day. Whilst lapping around the track, my oil pressure gauge was sitting around 6 or slightly above on the factory oil pressure gauge.

When coming into the pit area, the gauge was showing 2 and stayed at 2 whilst I let it idle for a few minutes. When I went out for my next laps it started out at 4 (where it normally sits in day to day driving), went up to and sat at around 6 or slightly above whilst on the track and back to 2 when coming back to the pit area and at idle again. This happened for two more sessions.

On the drive home it sat constant at 4 and has done so since when driving it daily. At idle, once warmed up, it used to sit at 4 also, however, it now goes down to 2 and then up to 4 once driving again.

The oil I am using is a 10W50 and have slightly more oil in the motor to cover any oil starvation issues when cornering and braking. Normally I would be using a 5W30 oil but my mechanic thought the 10W50 would be better for track purposes.

Any feedback would be appreciated.

Link to comment
https://www.sau.com.au/forums/topic/397329-oil-pressure-reading/
Share on other sites

As the oil heats up it gets thinner. It's being pumped with a positive displacement pump (kind of - not 100% but for this explanation we'll assume it is), and the pressure is caused by the resistance to flow within the engine (trhough bearings, etc). The higher you rev, the more oil it tries to pump (linearly proportional to the RPM). However, pushing the higher volume of oil through the same restriction causes pressure to rise (there's a bypass which prevents over pressurising the system)

On the track, the oil probably gets hotter than normal, therefore thinner than normal. This is why at idle, the pressure drops away. In normal driving, the oil won't get as hot or thin, hence the pressure remains a bit higher. Synthetic oils tend not to thin out as much at high temperatures, which is one of the reasons they're used in racing.

As the engine wears, the resistance to flow decreases, as the oil paths get bigger (more clearance in bearings etc.). You'll notice the idle speed oil pressure dropping away as the engine ages.

Sounds pretty normal.

Oh, as a side note, the numbering on your oil refers to its viscosity when it's hot and cold (5W30). The first number means it behaves like a single weight 5W oil when cold, and the secong number means it behaves like a single weight 30 grade oil when hot.

Hope that (over simplified) explanation makes some sense.

how bad is the stock gauge, i mean mine seems to work fairly well..I can easily notice differences in oils as the gauge behaves differently..

Speaking of which, ideally where should the gauge sit on a healthy motor??..

lately mine sits at about 3/4 line on throttle, then on idle slowly drops back to half..never goes under that i have noticed.

i changed to a 10/50...before it was a 5/40 and seemed to drop alot more quickly on idle and not get so high unless pushed hard...

Anyway, is it just normal behaviour and nothing to worry about or should I change back ???

Im tempted to put standard nissan oil in it just to see how it behaves...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
    • What ECU are you running? This is probably the biggest question. If it's a PowerFC, I'd probably change the ECU and get something newer that will handle the injectors in a nicer way.
    • FYI: Racebox RE7R Custom Tunes Released!   https://goracebox.com/.../2017-infiniti-q50-q60-re7r-tcm...   FOR GEN 2 (21+) VEHICLES, PLEASE SEE NOTE AT BOTTOM See more   But whomever tuned your car is the tuner you should go back to, AMS, Sonictune or BT Tune....
×
×
  • Create New...