Jump to content
SAU Community

Recommended Posts

Ok, I feel my GTS-T is feeling a little neglected so I'm considering a 100 hp shot of NOS on demand on WOT.

RB25/30 - GT3076R - Haltech Platinum 2000. 337 rwkw.

Good move ?, or should I save the dollars and wait until my kids pillage it all.

Link to comment
https://www.sau.com.au/forums/topic/398534-to-nos-or-not-to-nos/
Share on other sites

I don't drag it.

I'm hoping for a setup which the Haltech can introduce Nos only in certain gears , revs and at WOT.

But right now my injectors are maxed , my intercooler has 2 1/2 in and out, and I'm running stock manifold.

Will I still get anything more with NOS ?

I don't drag it.

I'm hoping for a setup which the Haltech can introduce Nos only in certain gears , revs and at WOT.

But right now my injectors are maxed , my intercooler has 2 1/2 in and out, and I'm running stock manifold.

Will I still get anything more with NOS ?

As long as your exhuast is up to the extra flow, yes you will see great gains. The stock intake manifold makes it easier to get a more even distrobution from single point of injection.

Your intake pipework etc wont affect the amount of extra power you can gain from nitrous.

The trick is to get the nitrous consistant. To do this you will need a bottle pressure gauge and heater on a pressure switch.

Is the engine still stock internally? If it is, I would suggest no more than 75ph fixed shot or 100hp progressive shot. If it's built, then think 100 fixed and 150 progressive, depending on boost pressure etc.

Cheers

Justin

Put a twin scroll 3788R on it instead!

I dont usually go for performance in limited quantities. Id prefer to know I can hoon interstate if I wanted to LOL

Le mans 24hr of Hoon

So get a G size bottle :woot:

Will lift the bonnet and intake manifold 10ft off the ground if it backfires though lol

Yeah... leanouts/nitrous backfires are pretty spectacular. Only ever seen them on carbied engines though... not saying it can't happen, but I've never heard of a backfire on a FI efi engine (engines that don't mix air and fuel inthe intake manifold 'plennum').

I think it's a great 'power adder'. There is no real trade off for the extra power when you'r not using it. For an extra 100hp of kick, you don't have to use a bigger turbo- more lag, you don't need bigger injectors- fuel economy/tune resolution, your not shifting the power curve up or down- if your using cams/cam gears, there's very minimal down time for install and it dosn't cost a bundle. Not to mention the dyno curve goes straight up at activation- ha ha ha!

Cheers

Justin

Thanks for all that info.

Yep car is built forged bottom end, Poncams, and Plazaman plenum.

Exhaust is stock ex manifold to 3 inch.

Intercooler has 2.5 either side.

3076 is 0.82 Ar, should have gone 1.06.

Running 21 psi now, does have more in it.

it does feel like its choking at high rpm

Edited by conan7772

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...