Jump to content
SAU Community

Recommended Posts

Hey Guys,

I'm looking to swap the stock gauges in my GTT (and maybe added one to the A-Pillar) to something from the Defi range (haven't decided which ones yet)

My question is to anyone that has changes the gauges, what's a better fit? 52mm or 60mm?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/398740-r34-gtt-gauge-swap/
Share on other sites

Hey Guys,

I'm looking to swap the stock gauges in my GTT (and maybe added one to the A-Pillar) to something from the Defi range (haven't decided which ones yet)

My question is to anyone that has changes the gauges, what's a better fit? 52mm or 60mm?

Cheers

There was a DIY thread on how to make them fit and look fairly stock.... I tried to find it but had no luck....

If you find it, post it up so i can see it lol.... There is cheap ones on Ebay that are stepper motor with warranty and in the same style as Defi, i love Defi but cant afford them so will likely go with the cheaper option, they are RACETECH or similar, they look the goods but have an annoying preset warning light for boost.

There was a DIY thread on how to make them fit and look fairly stock.... I tried to find it but had no luck....

If you find it, post it up so i can see it lol.... There is cheap ones on Ebay that are stepper motor with warranty and in the same style as Defi, i love Defi but cant afford them so will likely go with the cheaper option, they are RACETECH or similar, they look the goods but have an annoying preset warning light for boost.

Go Shadow Pro, Matt :) I've got them in my car, they work well and look exactly like Defi's.

yeah, it's kinda cool but an MFD just seems... under-utilised in a GTt

pic of my old GTt with gauges, from memory they were 52mm & a tiny gap between the window & the gauge, I made up a custom mounting bracket that screwed into the factory mounting holes for the original gauge cluster & held the gauges in place.

The small gap meant I was able to slightly angle the position of the gauges so they faced more towards the driver.

DSC04157.jpg

Thanks for the input guys

Looking through the DIY section people mentioned that a 60mm gauge will fit if you remove the window and 52mm if you leave it on

@Hanaldo, do you have a pic of the Shadow Pro in your car?

I've been looking at the Defi Racer series since you do not need the control unit. (http://www.defi-shop.com/products/rg/summary_rg/)

The only thing that concerns me is border that goes around the gauge and if that's going to fit properly even if I remove the window

Umm unfortunately I don't because at the same time as putting them in, I thought it would be a good idea to skin my gauge holder with carbon fibre, not realizing that the plastic expands and contracts with heat while the carbon fibre doesn't, so now it looks hideous. Not something I want to show off by any means.

If it helps though, they look like this:

WF3.jpg

Or something like this while mounted, but obviously in the 34 gauge holder not an S15:

nn5gmh.jpg

The backlights are fully adjustable, I didn't like them illuminated as much as they are in that picture so I turned them down. I've also got this video of my boost gauge, which is the same gauge just in the smoked face series:

Otherwise, my apologies for not being any help at all :P

Edited by Hanaldo
  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
    • To drain the Intake Heat Exchanger, there is a crappy drain plug in front of the driver's side front tyre: You should use the largest headed phillips screwdriver you had, and in my case I needed vice grips on the hose above as the plug was tight (tighter than it needed to be, since it has an o-ring seal).  After you have a tray down and open the drain, open the intake heat exchanger reservoir cap (drivers side one) and you should get a couple of litres of coolant To get to the radiator, you need to remove the plastic engine undertray. It is held on with a series of 10mm headed bolts and some clips. For the radiator, there is another type of crappy drain (kind of like a plastic banjo bolt) and you should attach a length of hose to direct the stream of coolant per this pic (otherwise the coolant hits the rad support and goes everywhere). The drain is on the rear of the radiator on the driver's side and a bit hard to find. Put a big tray or bucket down (5l won't be enough) and slowly unscrew the fitting by hand. You only want to remove it far enough for coolant to flow, it you unscrew it right out the whole fitting and direction pipe will come off and you will get a coolant bath (yum!). Undo the radiator reservoir cap and it should empty about 8l
    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You also need to drain the intake heat exchanger to remove the radiator so you will need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. 2 other tools that really help dealing with coolant lines and spring clamps are Bent Needle Nose pliers Hose pliers Between them they will reduce the frustration (and injury) potential by about 1000% Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
×
×
  • Create New...