Jump to content
SAU Community

Eoi Nm35 Nismo S-Tune Shocks And Springs.

Ross
 Share

Recommended Posts

Ross Collaborator

Ross

Posted
Posted (edited)

An opportunity to grab some coil overs for my stagea has come up, if they check out all good with no leaks this coming week my Nismo shocks and springs will be up for sale.

Would anyone be interested in the GAttack S Tune Nismos for $600?

Great condition, no leaks or noises. Comes with all literature and Installation certificates from new.

img1690ly8.jpg

p1030134z.jpg

Edited by Ross
Ross Collaborator

Ross

Posted
  • Author
Posted (edited)

20mm drop on 250t rs four, with much improved ride quality.

I'm in Perth , postage is no problem, should not run more than $60 or so anywhere in Oz.

Edited by Ross
Ross Collaborator

Ross

Posted
  • Author
Posted (edited)

The suspension is out of the car and ready for sale.

For installation you will need your stock Rear upper strut mounts and washer, as well as the rubber grommets on both top and bottem of rear springs.

I have also attached photos of the Nismos installed on car before i gave them a clean down, no leaks or grease anywhere, these are in great condition.

p1030158z.jpg

p1030156x.jpg

p1030153h.jpg

p1030154y.jpg

p1030155b.jpg

p1030159j.jpg

p1030160l.jpg

p1030162u.jpg

Edited by Ross
Howaitonaito Mentor

Howaitonaito

Posted
Posted

Would they be able to go in a V-sedan or not? Because I heard some you can and some you can't because of the rear weight over back end of the stagea?

Ross Collaborator

Ross

Posted
  • Author
Posted

These are from a 4wd Stagea, and from what im told 2wd and 4wd suspension is not compatable in between the two.

If you do have a 4wd sedan by some rare chance, i think they should work.

  • 2 weeks later...
Ross Collaborator

Ross

Posted
  • Author
Posted

Sus is now sold.

The drop is 20mm as the above have mentioned. Whilst its not crazy low, it does make the car much more responsive on turn in and flattens out the boat like characteristics of the car.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Manur33
      Rb25det coil loom wire identification

      By Manur33 · Posted

      Hi, i’m making a rb25det coil loom for Vag short coil. Can anybody tell me which Ecu signal wire belong to coil number 1 and 2,3,4,5,6? The connecting switch in above pic is 8 wire i think white is for +12v and black for earth.
    • davemoto63
      Stagea choice's which model??

      By davemoto63 · Posted

      Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • davemoto63
      Noobie Stagea owner..

      By davemoto63 · Posted

      Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
×
×
  • Create New...