Jump to content
SAU Community

Recommended Posts

Hey guys,my 33 has been off the road for a few weeks now,started off with no 1 fuel injector crapping itself and not shutting off. The injectors are sard 650ccs,got a new injector and now it seems no 1 splitfire coil is not working.Now what i need to know while i am waiting for another one can i drop the boost to 10 and use one of my stock coils or all and will i be able to drive my car ,so sick of walking. Genelle. :angry:

Link to comment
https://www.sau.com.au/forums/topic/399363-brocken-33/
Share on other sites

Omg i'm at my wits end,can not get the new injector to seal properly,have tried several o rings and it still won't seal.Does any one know what sort of o rings i need to fit a sard 650cc in the r33,any part no or advice much appreciated. :(

Link to comment
https://www.sau.com.au/forums/topic/399363-brocken-33/#findComment-6344084
Share on other sites

Check injector puls with a noid light or led test light. U need to see if the wiring is always powered and earthed which would keep the injector open

This was done with the old inejctor,all seemed good,but is not.Getting my 33 towed to a local shop tomorrow hope they can fix,you are a very helpful guy thank you so much for your advice,said shop said it might be pfc playing silly buggers,again thank you .Genelle. :happy:
Link to comment
https://www.sau.com.au/forums/topic/399363-brocken-33/#findComment-6345454
Share on other sites

Yay prob solved,was a loose wire shorting out making injector stay open,cheers for the help guys.Jezz i'll be in your neck of the woods in a few weeks time would be nice to meet you and have a chat.Genelle.

Glad its sorted. Something so simple can cause a major pain in the butt.

No worries give me a call / pm and we will organise a time.

Link to comment
https://www.sau.com.au/forums/topic/399363-brocken-33/#findComment-6347614
Share on other sites

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...