Jump to content
SAU Community

Need 5 Stud Conversion For My 32 Qld

Na boy

By Na boy,
in Wanted to Buy

 Share

Recommended Posts

N-DAWG Mentor

N-DAWG

Posted
Posted

Got 5 Stud Hubs/Upright Assembly from an R34 GTT Front Cut (114,000kms) if that's suitable. No Calipers unfortunately.

Located in Wollongong NSW 2500.

Postage arranged and paid by you, ideally by courier due to size and weight.

2011-11-11174323.jpg

2011-11-11174317.jpg

Also have these bits if you need them as part of your conversion:

th_2011-11-11174749.jpg

th_2011-11-11180116.jpg

th_2011-11-11180139.jpg

Na boy Collaborator

Na boy

Posted
  • Author
Posted

Thanks very much but i fear if i start with the r34 uprights then i may need to change more then i would if i went r32/33. Do you have any info on this ?

And can you tell me the bore on the marster plez

Thanks

N-DAWG Mentor

N-DAWG

Posted
Posted

Not sure the bore, but it's a BM44 part no. I believe it's the same between R34 25GT and GTT and also R33 (correct me if I'm wrong there) It seems to be quite common from my experience.

As far as I'm aware you would need matching Brake Calipers (bolt hole size) and correct size rotors, and the rest should be a bolt on job. Maybe brake lines? I got a front/rear set of ADR Approved Braided lines from Brakewest in Vic, was not much more than $200 iirc... They're street legal and better than experimenting with second hand rubber lines, and if you give him the measurements and caliper fittings he can custom make them which is what I had done.

Check in the Suspension/Braking/Handling Forum as I'm sure someone would have done same convesion/upgrade before.

This is of course presuming you're going to upgrade the brakes also. I would hardly recommend doing a 5 stud Upgrade on an R32 GTS purely for 5 stud wheel options alone...

I had my brakes upgraded from 5 Stud N/A Brakes to R33 GTSt items previous to a motor swap which is why I haven't used these to uprade my existing front brake set up.

N-DAWG Mentor

N-DAWG

Posted
Posted

Everything you see above $200 Plus Postage

Master Cylinder and Boost

Hand Break

Lines

5 stud hubs as pictured

Your choice whether you want the discs. I can measure the thickness on them to see if they've got much left or even legal thickness, but they might not be worth the cost to freight due to weight and you'll probably want a fresh pair.

I can package them up as best I can, though they are quite heavy. I know cause I had bought a pair previously from a member on here freighting them from Adelaide to Coopers Plains.

For $220 Plus Postage I can throw in a pair of Bendix Ultimate Pads to suit. I used them for a couple of months before switching to a more streetable compound so they have PLENTY of meat on them. Can send photos too if you like.

N-DAWG Mentor

N-DAWG

Posted
Posted

No worries will await your response.

I can do the master/booster combo $70 inclusive of postage on its own. Obviously if you want to arrange courier for the 5 stud hubs and the rest then the price is as above all together.

PM me when you know which way you want to go with it :)

Cheers

Nathan

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      R33 GTST Sh*tbox to Polished T*rd

      By Duncan · Posted

      Nice, thanks for sharing your progress....that's a pretty long list you are putting into it!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Decided to upgrade my pressurised plastic coolant expansion tank for a fancy pants alloy version The OEM versions can get brittle, even the new plastic one I got when I first got the car is a starting to show signs of "stress" I wasn't cheap, but it is basically unbreakable
    • pacman_1219
      RB25DET Neo Rebuild

      By pacman_1219 · Posted

      Morning all, I have an RB25DET Neo that's in need of a rebuild. Will need new pistons etc due to detonation damage. Would anyone be able to recommend a shop in Southeast Queensland who I could bring my long motor to for a rebuild? Just want someone who knows RBs and whos built a bunch of them before. TLDR - recommended engine shops for RB rebuild.
    • Yeetus
      R33 GTST Sh*tbox to Polished T*rd

      By Yeetus · Posted

      Gday Thought it was about time I started a build thread! As expected this project has snowballed into a huge financial liability, but unless you’re strong willed and responsible, it’s not a surprise. Background -  My first turbo car was an R32 GTS-4, got my full license and then totalled my Au Falcon a week later, so while trying to sell my RMZ450 dirtbike to buy another car a bloke offered to swap the R32 which at the time I felt like I was ripped off but looking back and seeing prices of those now ($40kish) it was a good deal, I didn’t know enough about these cars to appreciate what I had so sold it before the RB20 blew up. Between here and there, out of 12 cars I’ve owned the note worthy ones are a V8 Lexus SC400 (soarer), a couple of XR6 Turbos and my beloved S15 which I had for about 3 years, picked it up for $12500, repairable write off but she was fine, gun metal grey/pewter and bone stock/unmolested until I got my hands on it. Ended up spending about the value of the car and 280kw, 2 demerit points by the time I got defected and sold it for $14500 (also $40kish in today’s market, rip) Fast forward to the present day, I’m in a much better position financially and daily an MQ Triton (great cars, pipe down Ranger Bois), I cruised marketplace and car sales for a few months looking for another R32, the best deal I could find was an absolute rust bucket half finished project for $12000, until this R33 popped up in Port Macquarie for $18k - unregistered and barely running but decent shape, kept an eye on it for a few weeks and the price steadily dropped, $16k then $15k then $14k, that was the point where I was like shit someone’s gonna snatch this up! It was owned by a young bloke who had big plans but him and his missus just had a baby so smartest move financially for them but big gain for me. So 2 days later I’m towing a car trailer to pick this thing up. Roughly 2 weeks and $3500 later I’m cruising around Newcastle in my beat up R33 all smiles and dose noises! It only needed some basic shit to get it going, coil packs and air flow meter, electrical stuff and all fluids changed, 158k kms and running pretty good, nice smooth engine after oil and coolant flush - when I say coolant I mean it had been filled up with tap water, every gallery and heater element was filled with rust, 8-9 flushes later and still had brown liquid coming out but she’ll be right. The car was painted R34 Bayside Blue at some point but whether it was a cheap job or just not looked after is anyone’s guess, clear coat flaking like sausage roll.  Was rethinking my choices and contemplating life, had it up for sale for $22k - still cheaper than any registered R33 but got little interest, next minute I had an opportunity at work - 6 months overseas for good money, so that was a no brainer, fast forward again and here we are with a 50% finished project. Current Mods - 200ish KW according to butt dyno Was tuned with Apexi PowerFC EBC (old school Greddy Profec)  Stock turbo (more shaft play than a Tinder date gone right) 3inch turbo back Varex muffler  Aftermarket injectors of mystery size, Power FC showed 36% duty cycle at full boost so not behd good size Someone had good intentions but stuck with the stock R33 MAF so we had misfires at 6000rpm due to the MAF hitting 5.2V So far I’ve redone the entire interior with carpet form Car Mats Direct, new Seats and steering wheel from Autotechnica, also sound system by Autobarn (mainly Kicker) Also MCA pro comfort coil overs - Hands down best purchase yet, worlds of improvement over the tired 30yrold shocks Goals - 450kw/600hp on flex tune New paint job - Midnight Purple 2 Engine is at the shop getting rebuilt with forged rods a pistons, new valves and springs, ATI Harmonic balancer, Aeroflow 7.5L sump, rear head drain and oil restrictors as per oil control thread* and cam covers modded for larger breathers, other stuff I can’t recall of the top of my head Parts purchased and to be installed once the engine is done -  Engine loom from Wiring Specialties including these options: Haltech Nexus S3 R35 Coil pack conversion  PRP Dual Trigger kit Fan controller  Other Parts -  262 Kelford Cams Turbo - Hypergear ATR43SS3-ProS with T51R mod (whistly boi) 6 boost manifold (high mount) 50mm Turbosmart Pro gate (plumbed back for legal reasons) HKS Super Turbo Exhaust with High Flow Cat Custom 3.5inch dump and front pipe 1500cc Bosch injectors  Fuel Pump walbro 525 Haltech MAP and IAT sensors Haltech Flex Sensor Fenix Radiator with dual thermo fans LS1 Alternator Kit Oil Filter Relocation from EFI solutions and Cooling pro oil cooler Many other things sitting in my garage waiting for that engine to come back. Progress pics to follow -  
    • GTSBoy
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By GTSBoy · Posted

      Losses have to be less with DC coupling. Provided the battery inverter has decent MPP tracking ability - which really shouldn't be a problem. It's not 2005 any more.
×
×
  • Create New...