Jump to content
SAU Community

Rb25Det Stock Bov Leaking?

Ultimategtr
 Share

Recommended Posts

skylinecouple Experienced

skylinecouple

Posted
Posted

You only need a catch can if the motor is unhealthy. Just drill the appropriate sized hole into the intake and weld some pipe onto it then attach the breather pipe to it. All legal. Alternatively, cut a section of alloy pipe into the original rubber intake and away you go. You just have to remove the long and therefore softest section of the intake. Or yet again contact the many sponsors on Skylines Australia and get a new silicon intake.

Just do one change at a time and let us know how you go. Oh, and check all your earths just incase the car has been in an accident some time and they bolted the earth back up without scraping the paint away or left them loose.

Hanaldo Grand Master

Hanaldo

Posted
Posted

You only need a catch can if the motor is unhealthy. Just drill the appropriate sized hole into the intake and weld some pipe onto it then attach the breather pipe to it. All legal. Alternatively, cut a section of alloy pipe into the original rubber intake and away you go. You just have to remove the long and therefore softest section of the intake. Or yet again contact the many sponsors on Skylines Australia and get a new silicon intake.

Just do one change at a time and let us know how you go. Oh, and check all your earths just incase the car has been in an accident some time and they bolted the earth back up without scraping the paint away or left them loose.

Or if you track the car...

51NNA Community Regular

51NNA

Posted
Posted (edited)

This is why at the start I asked what intake and exhaust you have, the rubber intake hose will most likely be sucking shut...why not answer the question next time instead of saying you know its nothing to do with your turbo setup even though you have no idea about what happens when you leave a soft rubber intake hose on and what's the point in posting if you have already made you're mind up on what you're going to do?

Edited by 51NNA
The Mafia Grand Master

The Mafia

Posted
Posted

This is why at the start I asked what intake and exhaust you have, the rubber intake hose will most likely be sucking shut...why not answer the question next time instead of saying you know its nothing to do with your turbo setup even though you have no idea about what happens when you leave a soft rubber intake hose on and what's the point in posting if you have already made you're mind up on what you're going to do?

At what point do I seem ignorant? I'm sorry if seem ignorant, but I was just stating what I was experiencing.

I dont appreciate being called a fool, so careful with your words mate.

Well, I've proven my point.

What's the point if you're going to ask questions and then be a fool and not listen to the answers?

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      boost source Size Garrett gt28 gen2

      By TurboTapin · Posted

      You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • QB6SAGR
      Battle of the broken skylines

      By QB6SAGR · Posted

      Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Rezz
      Spotted on the street....

      By Rezz · Posted

      Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...