Jump to content
SAU Community

Recommended Posts

  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

agreed. Eventually.

You'll also notice your car might stall 'for no reason' at times depending on your driving style.

This is due to blocking the BOV.

The BOV is probably one of the only stock things that serves a half decent purpose (read: then I/C is crap as well as the stock turbo and the ECU to boot) I'd leave un-blocked.

Link to comment
https://www.sau.com.au/forums/topic/40021-the-flutter-sound/#findComment-819692
Share on other sites

your gonna notice if yur getting back fire that you are most likely chewing petrol, and yes it will affect you turbo, there are a lot of threads covering this, look them up.. theres a lot of mixed reviews, bootom line is ur std bov was put there for a reason. i know of a guy doing this to his pulsar et turbo, then his engine blew.

its your risk at the end of the day

Link to comment
https://www.sau.com.au/forums/topic/40021-the-flutter-sound/#findComment-820113
Share on other sites

Vl turbos dont come out with a bov, although i agree that they are there for a reason, i have had mine disconnected for along time now and no noticeable damage. Still goes alrite, um...at the end of the day if u want the noise without spending money on a ssq bov etc then it shte cheaper way out initially, maybe not in the long run.

Link to comment
https://www.sau.com.au/forums/topic/40021-the-flutter-sound/#findComment-820340
Share on other sites

i had two ets. both were pretty worked. when you installed the aftermarket (bosch) bov we had to block the stock bov. which we did by unscrewing the bov off and blocking it with a large type of screw that fitted in place. trust me man. maybe the previous owner took your stocky off???

its good to see a fellow n12 owner though, i had heaps of fun in those little things, my fiorst car when i was 15

Link to comment
https://www.sau.com.au/forums/topic/40021-the-flutter-sound/#findComment-820555
Share on other sites

Possibly... but the pipe from the turbo to the inlet looked factory. It was the start of my car hobby so wasn't as switched on about the ins and outs of turbo cars as i am now. But i never saw anything that looked like a bov. Mine was a 1984 model... perhaps they put them on the later models.

Link to comment
https://www.sau.com.au/forums/topic/40021-the-flutter-sound/#findComment-820619
Share on other sites

so his exa didn't have a bov either? interesting that nissan would put a bov on the ET but not the exa...

as for the flutter sound, i would be a little warey about trying to get it. It slows your turbo down so it has to build boost again after the gear change. Especially bad with a bigger turbo so perhaps not so much of an issue with the stock one.

Link to comment
https://www.sau.com.au/forums/topic/40021-the-flutter-sound/#findComment-820748
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
×
×
  • Create New...