Jump to content
SAU Community

Recommended Posts

So i have taken to putting in an aftermarket temp sensor and TEFBA inline filter into my cooling system. Naturally these both need to go into the top hose (outlet) which is sadly a very short and mildly convaluted.

I have modified the hose path to be able to get in the sensor uit and tefba filter with a set of hoses as shown.

I was just wondering from the people in the know (people just throwing out ideas and opinions try to hold back) if this is going to be ok and the cooling system is going to still work fine based on the hose path.

2 points worth noting.

-the hoses i have utilised are all sitting as per their original design. that is; there is no angles being forced on the hoses, nor any pulling or twisting going on that will cause the hose to crimp under heat/pressure.

-the hose is still always in an ascending gradient. it doesnt go up n down along its path from engine outlet to radiator inlet (see pics). it is still a steady upward gradient as per original design which im sure is necessary in coolant hoses.

This going to be fine or any reasons why not?

Obviously my main thought of issue is the 100 degree bend now utlised between the sensor and filter, which was not in the original RB25 design. However some cars do use such extreme bends in their radiator hosing so i can imagine why it would create and issue here...

cheers

Justin

post-68049-0-59589800-1337224595_thumb.jpg

post-68049-0-77348100-1337224607_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/400375-radiator-top-hose-modifications/
Share on other sites

Should be fine, but can I ask what purpose the filter serves? Naturally I can hazard a guess at what it does, but having seen a multitude of high performance engines and never coming across a filter in the cooling system before, I can't see why it would be necessary?

+1 for the inline filter.

If the cooling system is filled with the correct coolant, and replaced regularly; there is no need to filter anything.

Every joint you put in these hoses is just another potential point of failure.

Filter is good, Ive got one, when I had my engine rebuilt they installed one, it caught a heap of silicon and other shit from the rebuild, even though the motor was chemicaly cleaned it still got little bits of shit, mine is a RB25/30 so the block well over 20 yrs old, over that time no matter how good you maintain it the metals will breakdown, where does these little bits of rust and gunk go, through your water pump and/or blocking the cores of your radiator, unless you have a filter.

If they were not any use they wouldnt put them on new trucks and heavy plant, all our new trucks and heavy plant have colling system filters.

But if you happy to damage water pumps or have blockages in your radiator dont use one.

Engine rebuild 2 yrs ago (ish), coolant changed every oil change which is after every track day or on average 1000klm.

Track day tomorrow, this thread reminded me to check filter and clean.

Here is what it stops going through the system;

The proof is in the pudding.

couldnt agree more on the benefits of an in line radiator filter, the TEFBA filter has stainless mesh and is a quality item. . . im sure everyone knows here to use quality coolant and soft water but as just about all cars on this forum are secondhand who knows what the previous owner(s) have used in thier cooling systems?

Filter is good, Ive got one, when I had my engine rebuilt they installed one, it caught a heap of silicon and other shit from the rebuild, even though the motor was chemicaly cleaned it still got little bits of shit, mine is a RB25/30 so the block well over 20 yrs old, over that time no matter how good you maintain it the metals will breakdown, where does these little bits of rust and gunk go, through your water pump and/or blocking the cores of your radiator, unless you have a filter.

If they were not any use they wouldnt put them on new trucks and heavy plant, all our new trucks and heavy plant have colling system filters.

But if you happy to damage water pumps or have blockages in your radiator dont use one.

couldnt agree more on the benefits of an in line radiator filter, the TEFBA filter has stainless mesh and is a quality item. . . im sure everyone knows here to use quality coolant and soft water but as just about all cars on this forum are secondhand who knows what the previous owner(s) have used in thier cooling systems?

why use one?!

this and this.

N iv had several skylines now n been through the joys of 2 clogging radiators. We have near on 20yr old cars now that are notorious for doing it...

Also im now running some higher power through it and i live in perth with out lovely 46 degree days in summer. Want that thing running properly...

why use one?!

this and this.

N iv had several skylines now n been through the joys of 2 clogging radiators. We have near on 20yr old cars now that are notorious for doing it...

Also im now running some higher power through it and i live in perth with out lovely 46 degree days in summer. Want that thing running properly...

fark yeah, for the cost of a radiator cleanout and the possibility of a cooked engine its good insurance to have a filter

So i have taken to putting in an aftermarket temp sensor and TEFBA inline filter into my cooling system. Naturally these both need to go into the top hose (outlet) which is sadly a very short and mildly convaluted.

I have modified the hose path to be able to get in the sensor uit and tefba filter with a set of hoses as shown.

I was just wondering from the people in the know (people just throwing out ideas and opinions try to hold back) if this is going to be ok and the cooling system is going to still work fine based on the hose path.

2 points worth noting.

-the hoses i have utilised are all sitting as per their original design. that is; there is no angles being forced on the hoses, nor any pulling or twisting going on that will cause the hose to crimp under heat/pressure.

-the hose is still always in an ascending gradient. it doesnt go up n down along its path from engine outlet to radiator inlet (see pics). it is still a steady upward gradient as per original design which im sure is necessary in coolant hoses.

This going to be fine or any reasons why not?

Obviously my main thought of issue is the 100 degree bend now utlised between the sensor and filter, which was not in the original RB25 design. However some cars do use such extreme bends in their radiator hosing so i can imagine why it would create and issue here...

cheers

Justin

post-68049-0-59589800-1337224595_thumb.jpg

post-68049-0-77348100-1337224607_thumb.jpg

it should be fine if its still below the air bleeder on your cooling system

yep. below the bleeder and even radiator cap.

CLeaned it out for the first time last night n the mesh was clear but the magnet had lost of rusty flake residue...

Glad this thing is there if it is removing this kind of gunk...

Will update this with comments as in the next few weeks im going to run a flush through the system so ill tell you what gets caught when i do that.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...